borg computer case 3d models

Laser cut parts : plywood case (not essential). Spanish grocery crates give best engraving contrast (:-)) Small parts : tactile switches 6x6x12mm, power switch, micro SD adapter, CR2032 battery Source : Aliexpress, Ebay. If...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

&nbsp;I soldered leads to the core, and added a small plug that tucks away inside the back case. &nbsp;Then I soldered the corresponding small plug onto a USB charging cable.<br><br>&nbsp;</p><figure class="image image-style-align-center...

Just put the canopy glass inside the frame (unless you printed out the complete model, in which case this step is eliminated). To display the canopy open, canopy joint attaches onto the dashboard and the frame then attaches to the joint. ...

By pressing the STOP button, the so-called warning lights can also be switched on when all the turn signal lights do not light, when all the lights start flashing simultaneously. In order to operate the turn signals and especially the warning lights...

In this case, the person is not able to control his actions and can hurt even close people. Especially good about this is shown in the movie Van Helsing and Harry Potter.ABOUT THIS 3D MINIATUREThe model is saved in STL files, a format supported by...

I've included a screenshot of the outline of the 6.5mm version with dimensions in case anyone wants a starting point for their own, from scratch, design. -------------------------------------Fire-steel Striker---------------------------------- ...

14) Using the scissors, locate the gray ribbon cable on the large PCB you unscrewed in step 9, and cut it either: - Towards the center in case you want to revert back to a near-stock turntable. - Close to the large PCB to make soldering easier. ...

Together with the black background, the surface of the moon can thus be printed as a grayscale image and is easily recognizable.Clock movementMovements with a case size of 56 x 56 mm can be used for the movement. If necessary, the hands of the clock...

In this case as some of the walls may be a bit thin I went for an infill of 30%.For the Sonic Screwdriver / Grip part and the moldmaking gem / crystal I have additionally enabled supports. Optionally a 3-5mm brim can be used. The supports are of...

Each unit connects to a maximum of four more with standardized airtight corridors, which have an airlock in case there is a loss of pressure. The space between the Domes works as external Storage areas, and can be accessed from the connectors,...

Following items were ordered from a mail order plastics company, (Trent Plastics, in my case in UK). Parts list as follows:Acrylic tube, 16mm OD, 12mm ID x 1000mm lengthAcrylic Tube, 12mm OD, 08mm ID x 500mm lengthAcrylic rod, 8mm diameter x 1000mm...

I used variables in Fusion360 so you can just use it as “parametric” for your use case. Just let me know if you need other sizes.Design focusEasy and fast to printstable / rigid (printing orientation for maximum strength)Only minimal bridging (for...

Connect the male JST from the 1203BB 12VDC input to the female JST from the 12VDC 4A adapter. Using 4x M3 screws + bolts, secure the 1203BB board to the electronics case. You will need to remove the knob for the speed control first. ...<h3>Print...

In that case 17 of the 26 letters for the third letter make viable letter blocks, but there are no other viable blocks in any of the other 11 orientations with any of the 26 letters for the third letter. You can't tell from the preview which blocks...

Years ago, there were no other options for A-Pillar mounts, so bear with me here as there may be better options available now, I still wanted to share what I made in case anyone else goes this route, or maybe there are other 50mm Pod openings this...

The diffusor is symmetrical, so i sticked the foil on the nice side with the structure of the satin print sheet.I used Silhouette Studio for design the watch face and uploaded the .studio3 and also as a converted .svg for other plotter...

You must take it from the Buratinu Midi 1000 https://www.thingiverse.com/thing:4280142 Or in case you can print larger, you can take the parts from here: https://www.thingiverse.com/thing:3857570 The Buratinu 1300 uses the same fuselage as the...

Also a thicker one in case the thinner clip isn't strong enough.Read the tips below for the best result.If you want the most stable result, use the rubber pieces tip together with a stabilizer.I would be delighted to see pictures of your...

In some cases a little sanding may be needed to fit parts together. Linear advance will be to your advantage and to help minimize that "bow tie" effect (that's what I call it at least) on the corners of parts. Also use a deburring tool to clean up...

The bearings should sit tight and hold everything together, but if you want you can put some superglue on the lower part, just in case.Updatesv1.1: Slightly increased clamp width (152 vs. 150mm, new Customizer default)</i> for a looser fit <i>(if too...

Intro Media Control Knob inspired by Mikolas Zuza design: https://blog.prusaprinters.org/3d-print-an-oversized-media-control-volume-knob-arduino-basics/ I've changed the enclosure, code and used digispark instead of arduino so it's hard to call it a...

In addition, to avoid incidents, I have put a little edge on it so that in case of handling it it does not fall inside. It already happened to me with one that I downloaded and printed, which didn't go right in and came out. Then, moving the...

That will click a small micro-switch which will turn off the relay hidden inside the plastic casing of the power supply that will cut the main voltage. That way, the printer is totally and safely off. Compared to existing solutions, this one does...

Quick to print and potentially useful. Use Case I print with PETG and the MMU and have been dealing with long stringy tips after retraction. I installed an experimental dual-blade cutter that did a good job of cutting off the tips, and there were a...

In case you still observe a horizontal state, consider using a smaller magnet or increase the distance between magnet and reed contact.Files are updated and description is adjusted to v2.Items to re-print when updating: only Bucket and RainGaugeBase....

In case the parts aren't quite aligned you may not get a good first layer which may cause the print to fail. There is an easy fix for this though, just lower the print to actually go a bit below the print surface, since the print is same all the way...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

According to everything I have been able to understand, the contagion of the virus occurs, in almost all cases, when a healthy person comes into contact with fluids (Saliva or Secretions) from an infected person. This occurs when the infected person...

Additionally for your use case I have designed some more side modules.After many iterations I have further refined the system. The number of parts was reduced to the most necessary and the amount of filament needed was reduced. All components can be...