borg cube model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

I was unable to find a free CAD model of the G5 on the internet. assistant Greetings, I started this endeavor to obtain dimensions for making a wooden housing specifically for the front area of a G5 device. Could someone here help with creating more...

... There are probably better options, but I haven't investigated yet. You'll also need a Radio control receiver (and transmitter) (eg a Taranis). The X8R receiver really is too big for this size model, but it was all I had here so that's what I used.

... ...Allows you to now place RepWinders in your newer model RepBox without having to Remove the Slip Rods! UPDATED 10/29/19Print instructions3MF File set up for Default .2 layer height Prusament PETG PrusaSlicer profile. Can be done in PETG or PLA.

When you warm the bags, the plastic becomes brittle, and you end up with loose desiccant. 3-4-2019 UPDATE: The cereal containers are 21 cup size and can be found at Amazon here:...

I am keenly interested in optimizing this concept so that it Works for those needing a good, quality, multi-purpose coral frag plug so please leave comments on how I might improve this Thing. Instructions Additional fragging tools that might be of...

... clean it up.  Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).

This allows protecting the model against falling over.Printing configurationLayer height 0.2mm0.4mm nozzle15% infillWhite PETG filamentplace the two halves making the bottom part of the sensor housing to their sideno support except for the top...

Also also: if you get sick of chasing dice when they fire out of the bottom of the dice tower at high speed and scatter over the edge of the table, I would suggest you head over to [**domino6713's dice tower courtyard...

Perhaps my specific model of the C270 camera had some differences? Original "c270_hinge_M3_screw.stl" was missing a crucial constriction of the bore for the pin (as viewable in the original camera mount). The edge of it should form an inner lip for...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

I have reported this bug to the developers with this issue that they hopefully fix soon: https://github.com/tzapu/WiFiManager/issues/1609 —> Problem solved!04.07.2023: Release of software version V1.8.0:Replaced the old WiFi manager library with my...

It is not necessary to add this "torus".)Seam positions:   Aligned:  Pegs, Discs, Base, Storage Box Lids   Random:   Cover, storage box basesFilament color changes:If you want to use different colored filaments as I did,...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

I always wanted to design and print a swamp boat. Now it was time to realize it. The boat consists of two parts, which are screwed together. For sealing the whole thing is glued around the internal cable duct. I took the motor and ESC out of my MHQ...

... pictures are from Printable Heroes. They do not sponsor nor endorse these stands, but they do indeed offer a great variety of models —many of them for free. ...They do also have several, very affordable Patreon tiers —I suggest to check them out!

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Again tilt the drawing slightly, noting that you have the right corner vs the model orientation. It can get a little confusing. Save the Sketch 4. The spacer should automatically be tapered to match the corner height because the angled plane adjusts...

145°C die Mineralwerkstoffplatte zu biegenAuf den Bilden zum Projekt ist der Fertigungsprozess zu sehen.Druckdaten PLA Teile:Schichthöhe: 0,2mmInfill: 20%Schichten oben und unten: 3Wandlinien: 3Stützstruktur: keine Druckdaten PETG...

I also designed roller bearing(it was harder than I though) which works great (better than anything I found on thingy) but a also included modified gear bearing from emmett (https://www.thingiverse.com/thing:53451) which could potentialy be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I recently published the little project [Nano Pin Protector](http://www.thingiverse.com/thing:880427) that provides a shell for the widely used Arduino Nano and its many compatible models. Did you know that instead of using a Nano, which has an...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

While it worked okay for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to...

... 3D model created using SketchUp Make (free software). I also tried 45 degrees, but the fan's thickness made it touch the desk surface below, so it had to be skooted up to the high end of the stand... thus the cooling effect would be diminished.