brake line clamp 3d models

Simple bicycle brake line clamp designed to hold the brake line in place on frames that already support this style of brake line clamp.Print laying down and with 100% fill for best results.

replacement for: NISSAN Brake Line Pipe Clamp for R32 R33 R34 Skyline GTR 46289-15U10 Needs M3 16mm, 10mm bolts & nuts

The red front brake clamp on my cr500 broke, so I designed and manufactured one. Since installing this fabricated piece, I have navigated through some really harsh terrain at high and low speeds and it has performed fantastically. ... Print Settings...

Created for Houser XC A-Arms (YFZ). Can be changed for other A-arms, but would need to be resized. ... I used M8 hardware to tighten (13mm M8 nut)

Simple 'cushion' that allows brake lines to be safely attached to a car axle. I printed this in TPU with 100% fill to give a robust part. Attached to the axle of my 1963 Daimler SP250 (Dart) with a 'Jubilee Clip' style hose clamp it works very...

Broke my OEM clamp Just a rough sketch, yet the printed one is still in one piece after about 5 hours of riding. Might be a good idea to reinforce it. Maybe will post a V2 someday Update: V2 It broke after about ten hours and two races, dont know...

When converting a KTM 9x0 to a high front fender its common to use SX85 fork guards.But the right hand guard doesn't have a brake line clamp to stop the line going in the spokes. This design is a mirror image of the clamp on the left hand guard so it...

Simple way to safely clamp a brake or fuel line.Hardware:M6 x 50mm full thread hex boltM6 nut

Here is the rewritten text: I needed a simple replacement for a broken plastic clip on my bike, and it seemed like I'd have to choose between two types - but one would be enough to get the job done.

Bike Accessory: Shock Absorber Strap Retainer for Honda XR-250 Desert Rider Perfectly designed to secure brake line hose clamps on the Honda XR-250 Baja, this bike accessory will also fit similar motorcycles with a 53mm shock absorber diameter.

... these to hold the clamps in using a standard M6 bolt and rivnut on the firewall. ...made both the 4 Line clamp( closer to brake booster) and 3 Line clamp (other side of the engine on firewall) recommended to print in abs to withstand engine bay temps

These are clamps to mount 3/16" (.1875 Inch - 4.76mm) Brake Lines to Frame rails, bodies, or whatever you want. There is a Single version for mounting individual lines, or a double version. The Double version has a Hex recess for a 10-32 Screw...

Securely mount brake lines on your automotive project with these clamps for 3/16" (4.75mm) and 1/4" (6.35mm) tubing. The tubing is designed to snap in tightly and attaches with an M4 or similarly sized screw. ... Print with 1.2mm perimeter width and...

surron ebmx specific swing arm brake line clamp. ... replaces the plane jane clamp "loop" thing

This is a trial run to keep my pipeline fed and retrieve -6AN fuel hoses and 3/16ths brake hose.

This is a replacement for the original tube/cable clamps that run down the left frame of the Jeep Wrangler - TJ/LJ. The measurements differ from the original by incoporporating a 1-inch standoff. ... On my 2005 LJ Rubicon, the extra spacing was...

Z1000sx hel brake line clamp

This is a front brake guide set that I made in order to route a trailtech dash speedo wire along with my front brake line. This clamp is pretty stout and is a split-clamp design in order to install without removing any cables. PETG is highly...

Kawasaki KL Series Brake Line

Bicycle brake cable clamp for 37mm front fork diameter (SR Suntour MG91) and 5mm cable diameter.

This is a Shimano Hydraulic Brake Hose Clamp. Works on all Shimano-compatible brake hoses (~5mm diameter) Designed to help during brake bleeds, trimming down hoses and so on. Use it as a normal hose clamp. ... Recommend using 50% infill to keep strength...

Human: Turn Wheel Clamp.\r\n\r\nAdditional Required Hardware: M8 Hex Bolt, M8 Hex Nut\r\n\r\n

Hydraulic brake line standoff to help route and secure brake lines. ... Made for 53mm USD forks

I've fabricated a sheet metal brake specifically engineered to integrate seamlessly onto the DeWalt 12-inch large trigger clamp. ...With this custom-made tool, I've successfully bent 1mm steel with effortless ease.

Brake housing guides on my bicycle were severely damaged. ... I chose to manufacture brand-new ones. These are engineered to be securely attached to 26.5mm tubing. Additionally, you will require an M3 nut and bolt to effectively tighten the clamp.

Common bicycle clip that holds the brake line attached to the frame.

This is a clip that goes onto the a-arm to hold the brake cables of the Polaris Predator ATV. ... This replaces part #5435861 "Retainer, Brake Line, Front"

The essential tool for brake replacement, it blocks the brake fluid leak in the brake line. ...To assemble the tool, you will need two M8 nuts and two M8x45 or longer bolts.

fits the avid juicy series brake levers, maybe newer too