brake line clamp 3d models

Layer Hight: 0.16 Wall Thickness: 1.4 Wall Line Count: 3 Infill: 70% (maybe can be less, i tested with that) Infill Pattern: Cubic Subdivision Printing Temp: 196º Plate Temp: 45º Print Speed: 50mm/s Material: I used PLA but think the best for this...

Replacement brake line clips for the engine bay. ...A full replacement is two double row and one upper and lower

I created this to hold the 3 SAE brake line wrenches I have, and make another one in blue for the 3 Metric brake line wrenches I have. ...I have the Duralast brake line wrenches.The walls are 4mm wide and the slots are 6.9mm, 6.5mm, and 6mm to hold the...

Model for 3D printing.You need to heat up the spiral a little bit to bend it up an insert the brake line. ...After that bend it back.

Model for 3D printing.You need to heat up the spiral a little bit to bend it up an insert the brake line. ...After that bend it back.

These are designed to replace old broken factory brake line holders on a 2016 Yamaha yz450f dirtbike, can not confirm fitment on anything other than 16' yz450f.

This is a super basic brake line clip to hold two lines close together. The Parametric tube clip was working, except for the opening, to actually clip the line into! ...I modified it with a simple bool to open the clip to tight (100 degrees open) and...

Decided to make a modified rear brake line guide for my 2000 KX 500. The line clips into the bracket and I made a notch to add a zip tie for some extra security. This replaces Kawasaki part # 13070-1144. ...Not sure of the durability, they made it...

I'm upgrading my 2000 KX 500 with a custom rear brake line guide. The modified design clips seamlessly into place and incorporates a notch to secure a zip tie for added stability. ...This DIY upgrade replaces the original Kawasaki part number...

Human: Attaches .410 diameter brake line to sturdy 1.00 diameter front arms, securing it away from moving joints. Uses a robust 10-32 x 1.0 long socket head cap screw and a reliable 10-32 nylock nut. ...Specifically designed for the DF Goblin kit car,...

This one printed as is should work with a standard 3/16 brake line nut and if you print it at 125% size, it should fit a standard 1/4 brake line nut. It is a tight fit so wrenches are required to put the nuts on but that means it won't get...

Decided to craft a custom rear brake line guide for my trusty 2000 KX 500. The line clicks securely into place within the bracket and I carefully crafted a notch to allow for an added zip tie, providing extra peace of mind against any potential wear...

This device secures the elongated brake hose in place yet permits its movement.

Here is a replacement part for your Weinmann brakes, if you have the ones that have barrel adjusters then you can find those on thingiverse as well, these should just slot in as they are same dimensions as the originals, I think the curved part isn't...

Here is a replacement part for your Weinmann brakes, if you have the ones that have barrel adjusters then you can find those on thingiverse as well, these should just slot in as they are same dimensions as the originals, I think the curved part isn't...

This is for my 2005, it will probably work from 2002-2008 models. ... It is a replacement for the lower triple clamp brake line guide.

The clamping area in this section of the press brake ensures secure gripping and shaping of materials.

Front brake cable clamp YZ on the fork guard (The width of the fixation on the fork protector is 6mm)

Brake line clip for Peugeot 306 and maybe other models clip for6 brake lines

Citroen Saxo brake line holder with hole.

One Brake line routing for the bottom and one for the top fork.

1/4 Brake Line Bracket. ... Use rivet nut and bolt to secure.

Front brake line holder and horn mount for most Beta dirt bikes.

These parts are designed specifically for securing the rear brake line of the Honda XR650L in its correct position on the bike's rear swingarm. I've had my share of broken ones (no idea how it happened) and prefer not to invest in more fragile...

A brake hose clamp for RockShox Paragon fork. Mine is a Paragon Gold Air, but i suppose other version use the same system. The part clamping the hose is designed for a tight fit on a Shimano BH90 hose, but you could file the area for a looser fit or...

Replacing a broken brake line holder. Slightly optimized for 3D printing. ... Part number 11.4018.050.002

Clips that attache the rear brake line to the swing arm. ...Should fit most Beta dirt bikes.

Replacement part for a 2006 or later CRF450R brake line guide. ... Print Settings Printer Brand: Printrbot Printer Model: Printrbot Simple Metal Supported Materials: Yes Infill Density: 50%

Secures the brake line to the knuckle on many 1970, 1980s and early 1990s Audi and VW cars. ...OEM part # 811611797B Printed in nylon.

Since i didn't own a proper sim rig for my wheel I had to clamp this handbrake to my desktop with a ugly and big G-Clamp so I took the time and design this little clamp with marching holes for the base and a M16 nut as a clamping method. ... The inner...