c64 user port 3d models

This covers up the XG port but leaves the usb-c port open for use. There is two models. One is thinner and sits flusher but is harder to remove if you need to. The photo show the thinner one. ... Print as loaded 0.2mm layer height on a texture bed...

... connectivity. ...When the wifi is used, the ethernet port is left vacant and open. This can lead to insects making nests in the cavity ruining the port. This is a cap which can cover the port. ...No need of any glue or tape as this cap locs in place.

<h3>International Karate Figures</h3> <p>The iconic 8-bit player characters from <a href="https://en.wikipedia.org/wiki/International_Karate">International Karate</a>.</p> <p>Based on the Commodore 64 version.</p> <p><strong>BONUS:</strong> The...

Housing for SD2IEC interface, a creation born out of fascination for the Commodore 64, designed using Fusion360's powerful tools. No technical support is provided, but the design is open for anyone to use and adapt. To achieve an aesthetic look, the...

Design changed to fit with different cartridge desing. ... Holes are made for inserts for m3 screws.

Wall mount for Plexilaser Cases for the Ultimate 64.I designed the wall mount to have felt glued to the inside - to prevent the wall mount from scratching the case.Credits for the pictures go to @dwestbury , that's his system :)

A sleek and sturdy cover/case is provided for the SD2IEC, which can be easily snapped onto the device without the need for a cable. ...When directly connected to the Commodore 64, it adds an extra layer of protection and style to your gaming console.

Internal Housing for the SD2IEC in version 1.2 for the classic Commodore 64

I designed this cover plate to be used when replacing the PSU on a Commodore 64 1541 Disk Drive, feel free to use/modify it but done at your own risk. I used an M5x0.8 TAP on the attach holes so I could use the original transformer screws then...

So, this was my first 3D design I did back in 2016, and I published it on Thingiverse (it's still there). Recently, I've gone back and redesigned it to have a cleaner model and also made improvements on the original design with more flavors to choose...

Its biscottone one with all parts connected later its gonna be a lot better, No one ever here made this :) also has no keyboard,so it can be used as real case

One of the plungers of my keyboard broke down. I suspect I'm not the only one and I assume it's usually the top cross that snaps from the plunger. This part is designed to repair the plunger instead of replacing it. Keeping the unique feel that the...

Inspired by the fantastic Commodore 64 game from 1988 written by Steve Harter. These are the creatures from the game. If you know this game, this will be cool. I simply screen grabbed the image of the characters from this...

after my floppy fell down, I had to make a new base. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 15% Filament: doesn't matter PLA doesn't matter Notes: must disable "don't support...

For assembly required items:M3x20mm screw x4M3 nuts x4 M4x15mm screw x2M4 nuts x2Support is required only on the base place under the two buttons. ...It can be left in place and does not need to be removed.

I couldn't find any printable material for this Commodore 64 emulator, so I decided to draw it myself. Please use at least a 50% fill rate. Use a 2mm tip to make holes on the sides of the board as shown in the photos - these won't damage anything...

I have designed per request the original (older) 1541 specifically for the same sd2iec pcb, you can find it here: https://www.thingiverse.com/thing:3913444 This is a case for a DIY SD2IEC that's perfect for Commodore 8-bit computers. You can find...

This creation was crafted using Tinkercad's powerful tools. ...Modify it instantly at https://www.tinkercad.com/things/0rT9R5Vb2zK

This is a top cover for the 2in1 diagnostic/dead test cartridge for the Commodore 64. ... It has a label for each side of the cartridge embossed in it and has a hole for a reset switch.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/j8HszXAnQcP Category: Computer

after my floppy fell down, I had to make a new base. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 15% Filament: doesn't matter PLA doesn't matter Notes: must disable "don't support...

I created a simplified remix of the design found on https://www.thingiverse.com/thing:3273180, with all credit going to maciek717! To enhance functionality, I added the option to use two types of strain relief sleeves. Version 1 is designed for the...

The power supply consists from 10W transformer for delivering 9V AC and a Samsung 5V/2A USB charger for delivering 5V DC. ... The entire circuit is wired on a 90x70mm Universal Prototype PCB Hole Matrix board.

<p>I had some parts spare so made a housing for it.</p> <p>Joystick is a Sanwa style. The flat round dust cap for the stick fits into a recess in the top housing and is fitted before the stick is mounted. The sleeve and ball are attached from the top...

I recently helped out a buddy by adding a WiFi logo to a modified WiModem case that initially caught my eye thanks to the talented RolandJuno's design skills.

Custom Power Connector Cover for Ultimate 64 System Securely seal the gap surrounding the power connector.

# International Karate Figures The iconic 8-bit player characters from [International Karate](https://en.wikipedia.org/wiki/International_Karate). Based on the Commodore 64 version. __BONUS:__ The impartial referee is also available. ...:-)

Ultimate64 power connector cover. ...Close the gap around the power connector.

after my floppy fell down, I had to make a new base. ...

<p>This is my 1st design</p> <p>I haven't worked out the best way to print this, Any help post in the comments.</p> <p>Thanks</p> <p>edit</p> <p>added a version 2 with thicker walls</p> <p>edit 19/10/19</p> <p>added a version 4 with a curved inside...