cable chain brackets for printrbot classic 3d models

Quick and dirty update to the cable chain tray for the X axis. Allows the trays to be used without the need to relocate the Y endstop. ...This replaces the right-hand (from front of printer) piece of the X axis tray.

I've Simplified the printer settings to fit a compact X-Axis cable chain mount, which now allows the printer to sit perfectly on an IKEA Lack Printer table (available at thingiverse.com/thing:1843235). ... **Print Settings** * **Printer**: Anet A8 *...

20x10 Cable chain mount for BLV MGN Cube and Helmet extruder ( https://www.thingiverse.com/thing:4218238 ) There's still some deflection on X axis I'll correct someday. ... This is a remix inspired by https://www.thingiverse.com/thing:4099951

... the bed is heated to 110 degrees Fahrenheit, being careful not to burn your fingers in the process. Works optimally with part number: 611593 (Open Cable Chain). ... Print Settings: Rafts: No Supports: Yes Resolution: 0.2mm Infill: 30%

- thing_611593_Open_Cable_Chain_new-chain.scad: taken from https://www.thingiverse.com/thing:611593 - coté_extrudeur subdirectory: - Support_Chaine_Cable_sur_NEMA17.scad: the file used to generate the ring for the extruder motor. - Conception.scad:...

So I designed this low cost cable chainthe idea is for the chain to be inexpensive and modular, assemble the whole chain and put it into place, then remove the side and load the wire..I have included the f3d file.The chain plates are 3d printed with...

This was also remixed from the "Rambo-heatbed-cable-clip.stl" file for the "Original Prusa i3 MK2S -> MK2.5 upgrade" on this page: https://www.prusa3d.com/prusa-i3-printable-parts/ It's also worth noting that I used the following parts to connect...

This is inspired by Lawsy's http://www.thingiverse.com/thing:104817 chain cable that showcases impressive designs for custom hardware parts. I drew inspiration from this concept to create a wire bundle tube for my Solidoodle 4's Y-axis, which...

... The model combines main parts as separate entities, allowing for easy modification or removal of materials and replacement of standard parts. ...If you encounter difficulties separating standard parts, we're happy to provide qualified assistance.

I simply raised my mainboard 10 centimeters, which was for the purpose of both utilizing a great X-Axis chain without extending my hot end wiring, and left room to mount a mosfet below the mainboard. In any case, the mainboards backing plate must...

This is a case with cable chains for the Duet 3 Mini 5+ wifi board that is designed to fit onto the Prusa i3 Bear upgrade (https://www.thingiverse.com/thing:2808408) aluminium 20x20 extrusion frame using standard M5 bolts and t-nuts. The original...

Also, I was inspired by a YouTube video I saw; sorry, I can't remember how to find it, where the circuit board case had a connector for a cable chain. So I've added support for a chain from the X-stepper motor to the circuit board case. Finally, I...

I revamped it to integrate seamlessly with the aluminum extruder upgrade, allowing me to maintain full functionality of my cable chain system.

Bipsen's fan mount now boasts a secure cable chain end, ensuring a reliable connection. ...The modification was successfully printed, and the system is up and running smoothly.

This is a scaled-down version of the Y-axis/heatbed cable chain. ...There's now more clearance between the frame and the holder, a full 1 millimeter.

This remix was created by combining two great designs. ...The main purpose of the design is to fulfill both the cable chain function and the filament guide function. ...

This is my Cable Management System for RJ45 Keystone at MPCNC Primo all Versions.It´s a Remake or a Remixe from different sources:The  Original Cable Chain parts you can find at: https://www.thingiverse.com/thing:4541775 made by jmillerfo July...

I liked the first cable chain design very much, so I added just a top link hanger element - small piece attached on a side by two micro screws, that can be hanged on the original cable ribbon clip.

I did not want to loose 20mm from having the cable chain behind the Z rods. ...So i pulled them out by about 60mm and added a nice cable guide on the stepper mount.

I was really impressed by jbhugh's cable chain design, and I saw a lot of potential for improvement. The only thing that bothered me about the connection was having to drill holes under my heated bed - it just didn't seem like the most elegant...

UPDATED VERSION:Taller Supports were added to prevent the chain from touching the frame screws. Cable chain and supports for flying bear ghost 5.Supports are Suitable for a 10x20 cable chain:Link for buy: Buy the Chainor you can print directly...

2) For every chain, pinch the joint hard (where is connects to the next chain) and rotate the joint repeatedly for 5 - 6 times. This will result in the wear of some plastic, causing it to be more smooth. Do so until the joints move with ease. This...

I made a track that fits in the Cable chain Brackets. ...Works nice as a guide for the chain.

On my Tronxy X5SA (no Pro, no 2E) the mounts of the horizontal cable drag chain have a difference in height level of about 3mm, i.e. the printhead mounted end of the drag chain is 3mm below the frame mounted end. So I remixed this...

On my Tronxy X5SA (no Pro, no 2E) the mounts of the horizontal cable drag chain have a difference in height level of about 3mm, i.e. the printhead mounted end of the drag chain is 3mm below the frame mounted end. So I remixed this...

I needed a mount for the micro-swiss bowden extruder for a cable chain. I couldn't find one for that, so I plopped it a different one into Tinkercad and came up with this. It's not beautiful, but it works (and isn't hideous). ... Definitely going to...

After printing the connectors for Beh01der's cable chain, I discovered that the clip to fit over the cable on the bed was much too narrow for my printer. I'm guessing that they've changed the design of that part at some point. I designed a new part...

Look no further, I've got a nifty solution for that: two slick clamps for an igus e-chain (Series 045). Simply print, link to chain, mount it as instructed and voila... Your bed can now move freely without any hiccups. The perfect fix you've been...

For the X-axis, you'll need 16 cable chain sections, and for the Z-axis, you'll need 21 sections. Now let's begin! First, print the hot end head. This part doesn't require any screws; it fits on top of the metal plate from the hot end. Print with...

I like the BIQU H2 mount Ender 6 CoreXY cable chain now there one peice why not have the together first time haven't printed yet work in progress update soon with test fit Version 2.0 moved the cable chain so there's room to add filament