cable mod 3d models
124909 3d models found related to cable mod.prusaprinters
Description on reddit: https://www.reddit.com/r/headphones/comments/4060mp/i_have_finalized_my_hd_25_detachable_cable_mod/ If you want design files, ask.
thingiverse
Reversable cable mod for beyerdymanic headphones. (No need to drill a hole in the earcups) It uses the original retention clip used to hold the cable. The mini- XLR ports I used have a diameter of 10.5mm and are 17mm long. You might need to shorten...
thingiverse
Things you need: - 2x DB37 connectors (male & female) - Some cable - Some screws (spare screws from CR-10 will do the trick) - Printed connector box - 2x printed DB37 housing - Some patience when soldering all the wires :) I've used an old printer...
thingiverse
Instructions Minimal instructions if you have a stock printrbot print a extruder-to-bodwen and a bowden-to-hotend Install the Pneufit adapters on your bowden cable and screw it onto the 2 printed pieces install this on your printer Extended...
thingiverse
This part is for the mod described here: https://www.reddit.com/r/headphones/comments/4060mp/i_have_finalized_my_hd_25_detachable_cable_mod/
thingiverse
... to DIP adapter PCB (approx. 14x16mm) - https://ebay.to/2m65fTF - JST PH 2.0mm 5pin connector - https://ebay.to/2lEUdEz - approx 17cm of 4wire cable (I cut an old usb cable) - 2x M2 7mm screw - 3d printed cable mod If you like it - buy me a beer :)
thingiverse
I've decided to buy the Superlux HD681 Headphones and mod them to use a detachable cable with them (and with the V-Moda BoomPro Microphone). I didn't find any tutorials on how to do this so I decided to do this on my own. I've bought stereo 3.5 mm...
thingiverse
My cable was at the end of its life and so the headphones were thrown in the cabinet to be forgotten about, until I created a fix for them. Since I am learning 3d design and cad I decided to make my own part. There is one other part on here that...
prusaprinters
So basically I really like these headphones, and my only real gripe with them is the long cable which is nice at the desk, but annoying to use with a phone in the pocket.Many headphones solve this by having a plug instead, and supplying you with...
thingiverse
Many headphones solve this by having a plug instead, and supplying you with multiple cables (sometimes even with a microphone, so you can call your nanny with them). Since the SR850 (and other similar headphones) have their a fixed cable terminated...
thingiverse
I have adapted some pieces of the excellent work of yggdrazill31 for the U30: - Carriage support (the original one came to hit on the stud) - A small cover to hold the cables (you may need to print it at 99% to have a tight fit) - Support Z (too...
cults3d
I have adapted some pieces of the excellent work of yggdrazill31 for the U30: - Carriage support (the original one came to hit on the stud) - A small cover to hold the cables (you may need to print it at 99% to have a tight fit) - Support Z (too...
thingiverse
Parts to convert Printrbot LC extruder to bowden cable feed: -- Extruder to bowden including X-idler mounting bracket and insert -- Bowden to hotend This is for 3mm filament. Instructions This is a...
thingiverse
This is an easy mod to use any 3.5mm jack cable with your monoprice modern retro. No different screws required. This maintains a factory look, only the cup protrudes about 8mm more. This also gets rid of the annoying rattle from the original cable. I...
thingiverse
Two-piece cable retainer for the HP Reverb G1 VR headset that allows plugging in the DisplayPort+USB cable directly to the motherboard, bypassing the factory cable and its Oculink connector which have a high failure rate.
thingiverse
Cap to give the superlux HD668B a female detachable cable (Instead of the existing male detachable cable). Also usable for comparible headphones that use the same end cap. ...
pinshape
I used these panel mount 3.5mm jacks and some wire from an old Ethernet cable. I have sanded and painted the example in the photos and you could also print a second one and install it on the opposite side to allow the headphones to use a balanced...
thingiverse
This is used so that I don't have to cut into my inner headphone housing to fit the jack, as is done in [this instructable.](https://www.instructables.com/id/Audio-Technica-ATH-M50s-removable-cable-mod/). I printed in Amazon PETG at 0.2mm. ...Could...
prusaprinters
<p>I designed this part to add a jack to my AKG K240 Monitor headphones without permanently modifying them. The part replaces one of the existing pieces on the headphones and holds a 3.5mm jack from Adafruit (https://www.adafruit.com/product/3692). I...
thingiverse
I made this after printing some of the original and catching my thumb in the ratchet :-( this little mod saves your thumb :-) Flip the model 180 degrees to get the longest side on the print bed. ... 70% fill 0.2 res Thanks again to Mike
thingiverse
An update to thing:697545 by MechEngineerMike to make it snap-together. ... [3/10/15 update: sorry for the duplicate files in the first version... it's my first upload] Instructions Full size for extensions cords, scale at .5 for small cables.
thingiverse
**Print List :** 1 of X-Carriage Mount 1 of X-Carriage Lid 1 of Base Mount 1 of Cable Mount - to Frame 1 of Cable Mount - Link 1 of Ribbon Bracket x of Cable Mount - Link as required - I used 23 for my 300 x 200 printer, they fit together...
thingiverse
Original PRUSA MK3 Cable chain mod Rework. ... This is a mix with cable chain on yz-axis and flexible sleeve on x-axis in view to manage space for the MMU2, I think the MMU is non-compliant with the x-axis chain cable.
thingiverse
This is a Vertical Cable Chain Mod for the AnyCubic Chiron the does NOT use any additional hardware, bolts, screws, nuts, etc... I completely remodeled each file using Solidworks, but did take inspiration from linked remix; I just couldnt find...
thingiverse
Simple Cable Chain Mount mod I made for my BLV MGN. I made this because my cable wires always falls on the bed and hits the belts. It's not perfect, but it works! My printer is 400x400mm and the cable chain is very long. I think its perfect for...
thingiverse
This is basically a quick and easy to print mod for AnkerMake M5C that kinks the cable running to the extruder slightly to prevent it leaning back and catching on the Z pillar. You'll need main part of the mod, and to print two of the caps which...
thingiverse
... and wanted to mod it, so the described problems won't happen again. ##### I designed this little mod that can be glued on the chrome cap and the cable, as seen in the pictures. It will prevent the movement of the cable and fix the problems. ...
thingiverse
A Mod for the Winter One SFFPC Case Moves the Power Cable Up and Out of the way of the G1/4 port on a Bottom Radiator in Winter One. Might help with cable routing. Note this does leave the "tail" of the PSU Power Cable Extender hanging out. Consider...
thingiverse
-------------------------------------------------------------------------------------------------------------- ENG Although alexberkowitz's original is great and fully functional, I found it awkward to store the cable in the holder that comes with...