cable stabilizer 3d models

Work in progress but should work to stabilize cables when the base is slid under the laptop and the cables fed through. ...The two slots are to allow for a velco strap to loom the cables and keep them more firmly in place.

my cables broke every time so i create this:

Optional accessorie for 'Kossel effector' https://www.thingiverse.com/thing:747286 I added this part, to reduce the mechanical force on the cables and the PTFE tube!!! ... Just cut an M4 thread into the 2 unused holes / Fix with 2x M4x10mm screws and...

... sided Tape and "BAMM" it works. As always feel free to ask in german or english (but I'm not that active anymore, so may take a while) Edit: Cable I use is: "CABLETEX 5 Meter Oculus Quest 2 Link USB C" https://www.amazon.de/gp/product/B08N6HRX9P

FOR OFFICIAL OCULUS LINK CABLE (may work with others, but unlikely) Modified version (original by AlucardWulf) to fit my Link Cable. I'm not sure if later S/Ns are different than what it was originally designed to fit, but it was very tight on my...

FOR OFFICIAL OCULUS LINK CABLE (may work with others, but unlikely) Modified version (original by AlucardWulf) to fit my Link Cable. I'm not sure if later S/Ns are different than what it was originally designed to fit, but it was very tight on my...

I don't want to buy a new one or punish the manufacturer so I tried to stabilize it. After a few messurements (can add them with technical drawings if there will be a need for that), i sketched something thats (always should be) easy printable. Some...

I don't want to buy a new one or punish the manufacturer so I tried to stabilize it. After a few messurements (can add them with technical drawings if there will be a need for that), i sketched something thats (always should be) easy printable. Some...

I took it upon myself to throw together a better solution that wrapped around the extruder stepper motor and provided some spots to tight the cable down to so that it didn't wear out the cables prematurely. Printed in Matterhackers PETG on a MK3s+...

I had a minor issue keeping my cable support stable on the Vzbot Printhead and found this simple stabilizer corrected the issue for me it is press-fit like picture shows.

This is for use with the VzBot Print head from F3D Racing. ...I had issues with cable support wanting to move causing z height issues for my Bl Touch so I designed this to assist in keeping the support arm straight it is press-fit as seen in the picture

I hated the wiggly Thunderbolt cable on my **MSI GS60 6QE** so I designed a simple stabilizer. You can add slim felt pads to protect housing against (possible?) scratches. I also added a SkechUp file. My print settings are down in the notes. **!

this is an alternativ to the heatbed cable chain many are using just use TPU, no supports required

This will protect the printhead cable from quick damage. Turns the cable to the desired safe angle. No any chain needed. :) It is Compatible with the Normal S1 & Pro & Plus! (Supports are not needed if you use the print position as in the...

Small piece to protect the usb-c port. ... Should fit on a ThinkPad Universal USB-C Dock (40AY...)

(You need 2 M5 bolts, 2 M3 bolts, 2 M3 nuts Cable and adjustment: Make a cable loop and fasten on the low right cable holder. The lay the cable as seen on the pictures and again make a loop at the right cable holder. Tighten the cable by lowering...

The original part wasn't strong enough for my application, so i made a version that is strong enough for my needs. Also provided are some picures of my printer that show my setup. On the pictures you can see that the tentioner i use, doesn't collide...

Get cables out of the way and not rubbing on the stabilizer body. Included is the guide itself and a spacer needed to mount properly. Spacer should be metal and you need 2 of them. Hardware is not included, but you will need 2 bolts that are ~15mm...

If you build this Do NOT over tighten the nuts on the rod as this may crack the frame, Its only intended to stabilize the two acrylic plates and not change alignment. You will need: 6x M8 nuts(*i used two nylock 1 in each outer cap and 4 normal...

designed for small tripod, cellular phone holder

This is a remix of both the Easy Print Cable Chain, and also the Z-Axis stabilizer (https://www.thingiverse.com/thing:2481705), I modified both designs to work well for my machine. In combination it helps reduce Z-wobble and also maintains a good...

I use PLA for Print this. ... Thanks for Download this Model ;) How I Designed This

Quick and simple remix to use on my own printer.

... You can then also use the printable T-Nuts here: https://www.thingiverse.com/thing:3050607 Vertical supports added below bolt holes to enable easier printing especially in ABS where no cooling fans are used. Hot end cable hanger added. ...

When working with the cables, you may want to first remove the metal shield of the rods, snap the holder onto the rods at a position lower than the upper case of the printer, put the cable(s) through the holder, and finally push the holder upwards...

I really like the z-stabilizer with dual-bearing filament guide arm on the left of my Ender 3, so when I installed dual z-motors with a second lead screw I chose not to use the supplied bearing stabilizers in the dual-z kit, but instead to keep my...

stabilizer render 3d modelling

Fortnite BackBling Stabilizer

compound bow stabilizer

stabilizer https://www.youtube.com/watch?v=bvdrQod-IKs Print Settings Printer: wanhao Rafts: Yes Supports: Yes Resolution: 0,1-0,4 Infill: 50-100