cad modeling practice

I made a simple 3D model of the MKS SBASE board with the locations of the components I needed to be concerned with. You can use MKS_Sbase_CircuitBoard_Layout_Rev2.scad to adjust any of these that might vary for your board. I remixed this to be...

The receptical for the battery is based on a project by "fcauwe" on printables.com called: "Mobile power supply (DPS3005) with black and decker battery (freecad files included) "...

I only own the flat styled one, so that's the one I used to model the part in SW. I think they are both called QuickClick. I believe I may have the older version, &amp; that they've been replaced by the round style (see further down).</p> <p>I can't...

- An increase of thickness from 0.5mm to 0.6mm, which should allow a wider variety of resolutions and nozzle sizes to print the design and make the end-products more reliable between printer models. Thank you again for your support and enthusiasm...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Using the paint supports tool in PrusaSlicer, put supports around the square cutout that you can see by looking through the bottom of the model. Look at the image below for reference.</p><figure class="image image-style-align-center image_resized"...

... differences. As always please share any thoughts or feedback for further discussion and help each other move forward in design solutions, modifications for use on 3d printers like this model. ...These files were originally made with Tinkercad too.

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

### THIS MODEL IS OUTDATED: PLEASE GO TO https://www.thingiverse.com/thing:4712534 FOR THE MOST UP TO DATE VERSION ### Summary of the T240R- *Top 240 mm Radiator* mount for the Coolermaster NR200 ITX case. This is a mounting assembly/system mod for...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

V1 arm is fine too, but there's a risk of collision with some models of the head in very rare cases of high and wide prints. Prepare all parts. Power off the printer. Unplug the power cable! Disconnect the low voltage connector (2 wires). Unscrew...

It is intended to be loosely attached, for quick removal during total eclipse photography, and as a result, may not remain well attached in a windy or gusty environment.Materials neededPLA or another rigid filament for the frame pieces.Flexible...

... can get rather hot. PLA may work; I'm not sure. Use a minimum of: 3 perimeters 20% infill 4 top and bottom layers The model for the base plate isn't oriented correctly-- print it flat with the side labeled "TOP" upwards. Category: 3D Printer Parts

... class="media"><oembed url="https://vimeo.com/758042056"></oembed></figure><p>Gear ratio =2&nbsp;</p><p>STL are given on the recommended printing orientation, <strong>no supports needed</strong>. all models fit a prusa mini.&nbsp;

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Included is a list of hardware & electronics that can be used, a number of custom designed parts, and links to other Thingiverse parts to aid in completing this as a fully functioning RC model. All parts were printed in PLA, with 25% infill, and...

Step 1: Use a 3D modelling program (i used Fusion 360) Step 2: Create a solid layer which is as thick as your first layer (0.2mm for example) This first layer will be the layer which touches the print bed. I used a glass bed for almost perfect...

Again tilt the drawing slightly, noting that you have the right corner vs the model orientation. It can get a little confusing. Save the Sketch 4. The spacer should automatically be tapered to match the corner height because the angled plane adjusts...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

THis also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

This is how it should look like:You can use support enforcers to remove the unnecessary supports in the slots for the IO of the electronics (it works by bridging)I printed it at 0.3mm layer height, 10% infill.If your bed is too small, you can split...

... glad to finally get this published. Any questions about the historical nature of this set can be addressed to Simon at the email address above, and I will try to answer anything on modelling or future edits here in comments. ... -Ian R.

…unless you got yourself a special edition of a bobby car like a Porsche, Mercedes or the older Audi, VW or BMW models like I got. At most of the special edition you can’t fit the original push bar. I found the design of Klein-laui on thingiverse...

Also, when you ping your AirTag no sound is blocked by the print. It also has a small hole so you can use it with a cord or keychain.Parts descriptionThis printable model is made of 4 parts: Casing: this is the central part, the thick ring with a...

Printing horizontally for increased strength meant the tube experienced a little shrinkage (9% horizontally, 1% vertically), so I made a bigger model (Tube_40mm_account_for_shrinkage.stl) that accounted for this shrinkage, which worked perfectly. ...

Included with this design is the original (unmodified) hull files, a number of custom designed parts, an example list of hardware & electronics that can be used, and links to other Thingiverse parts to aid in completing this as a fully functioning...

Don't forget to like this model and Share it with as many people as you can if it's helpful to you! Keep On Growing! <Center><B>03/08/2022 UPDATE!</B></Center> <U><Center>THERE AREN'T ANY RETAILERS AUTHORIZED TO SELL THIS DESIGN!</U></Center> ...