calibration cube ender 3 v2 3d models

Remix del siguiente carro Satsana para ender 3 v2 https://www.thingiverse.com/thing:4623647 La idea a la hora de hacer este diseño es tener una pieza que se ajuste a la placa del carro modo plug and play, para hacerlo todo mas sencillo a la hora de...

It also fits onto the rubber feet on my Ender 3 V2 (better). In order to install a new motherboard-cover I additionally used these riser feet (https://www.thingiverse.com/thing:4665097). As far as I can remember my engingeering-courses the...

I needed to put my Ender 3 V2 Y-Axis endstop further than it originally is, so I had to remix one I found to achieve that.Keep in mind that the adjustability is not that great, as at some point (unless you modify your Y Stepper mount) your bed will...

This is a stand off for mounting my Ender 3 v2's power supply on the underside of my Ikea Lack enclosure. Print two PSU Secures to the mounts with 4 m3x8 cap screw. The mount then is secured to the enclosure by some screws I found in my garage....

Cable Management System: A Simple Cable Guide for Ender 3 V2's PSU. This cable management system mounts directly to the end of your 80/20 extrusion, utilizing threaded M5 screws with up to .35 diameter heads. To print this cable guide, use PETG...

Maybe I'm doing something wrong, but on my Ender 3 v2, the Z-axis limiter sits too high when I'm not using the glass bed. I usually loosen the bolts and slide it down a little if I need to, but there is a small plastic tab that has to be maneuvered...

I wanted a mount that worked with my Ender 3 S1 and couldn't find one for the Wyze cam V2, so I took a mount that I liked, added the Wyze bracket to it and then added a little reinforcement. It works. It's pretty good. If I was better with CAD,...

This is a drawer-based mount for a BTT Octopus v1.1 board on an Ender 3 v2 printer. This is a rough work-in-progress, and I haven't tested this current version on my own machine, so buyer beware. You'll need to remove the stock board mount and tool...

I wanted to mount my PI Camera from the x-axis and found HanKimMN Ender 3 V2 X Axis Mount. However, I have the CR Touch installed, and the head couldn't contact the limit switch. To address it, I took the same general design, and cut out portions...

... the right side. For right side optional drawer see: https://www.thingiverse.com/thing:5138213 or https://www.thingiverse.com/thing:5138213 It's my first remix ever, so any suggestions are welcome. Printed and fitted on my Ender 3 V2 Neo.

Designed for Ender 3 V2. Lights are a USB Light from Amazon: https://www.amazon.com/gp/product/B0828GJM2M?ie=UTF8&psc=1&linkCode=sl1&tag=solbui-20&linkId=476464368ea0b5ed1b011663cb01622c&language=en_US&ref_=as_li_ss_tl Here's the switches: ...

... Ender 3 v2 spool holder. Allows a low mounting option for the filament spool and angles it for less resistance feeding into the extruder. ... Prints without supports when oriented inside your slicer, the same way as shows in the image.

This is a X-Carriege for the ender 3 v2  with the mod  of linear rails (MGN12H), its very simple but works...

Seems the Ender 3 V2 rubber feet are slightly taller. This is one of two pieces, for other piece check out the original design - https://www.thingiverse.com/thing:3541279, damper_feet_4040_-_A_-_rubber.stl is the one used. ... Here are some...

This is a drawer-based mount for a BTT Octopus v1.1 board on an Ender 3 v2 printer. This is a rough work-in-progress, and I haven't tested this current version on my own machine, so buyer beware. You'll need to remove the stock board mount and tool...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

This is a remix of the Voron Sexbolt Z endstop for use on my Ender 3 v2. This fits the [hartk Z endstop board](https://www.amazon.com/gp/product/B09YGGQ8GZ/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1). I used 2x M4x6 screws and T-Nuts to secure...

A remix of the Ender 3 V2 BLTouch mount originally published by Bertram69, link: https://www.thingiverse.com/thing:4563093. The original part did not fit my printer without filing, so I simply added a cutout to make room for the wheel bolt head. ...

I designed this part to fit on the corner of the bed of the Creality Ender 3 V2. I used a vernier calliper to measure the exact thickness and its 7,05 mm, might fit for other printers as well. The first fit will be quite tight, don't worry about...

My recently acquired Ender 3 V2 had an issue where the X axis home position was over the edge of the bed. I was trying to print a panel that was pretty much the full width of the surface when I discovered this. The easiest way to solve the issue...

Replaces the stock drawer on a Creality Ender 3 V2 Printer. Fill it with a raspberry pi and other electronics such as PSU Relay. Mounting is easy, just remove the cap from the right extruded aluminium profile, and the Y tensioner. Slide the original...

Remix del siguiente carro Satsana para ender 3 v2 https://www.thingiverse.com/thing:4623647 La idea a la hora de hacer este diseño es tener una pieza que se ajuste a la placa del carro modo plug and play, para hacerlo todo mas sencillo a la hora de...

I wanted to adapt this design originally by Swarti to work with my Ender 3 V2. The original sat a few mm to low to actuate the switch. I doubled the thickness where the piece attaches to the printer rail and it brought up the switch lever to the...

Ender 3 V2 Satsana Grills U P D A T E: ALL NEW GRILLS FOUND HERE-> https://www.thingiverse.com/thing:5259880/files These grills have a tab that slides into the gap above front fan. This fits perfectly for my build, but you may want to make the tab...

I discovered a crack in my original x-tension housing, so I decided to make a new one, but based on the original tension system of the ender 3 v2.I also made it thicker and more robust then the original.If you need a longer version for "longer"...

Was struggling to find a good DTI mount for my Ender 3 v2. I didn't like the mounts that fit over the fan shroud because it kept moving around. This bracket fits into the pre tapped holes where a BL touch is normally fitted. The diameter of the...

... wouldn't slide in the base without massive force because of the rubber feet that are on the camera so I also made notches to accommodate. I added spring seats where it mounts to the bed. I also added the text "Ender 3 V2" on the face of it.

I dropped my Ender 3 v2 on the floor like a potato, so I thought I'd punish myself by painstakingly measuring the broken one with a caliper and re-creating it in TinkerCAD. I thought when they say to try power cycling it, it meant drop on floor...

This is for ender 3 v2's inside of an enclosure after the PSU has been moved outside of the enclosure. Requires some long M5 bolts, longer than stock M3 bolt for mounting stock Y axis endstop housing, and some GT2 idler pulleys (one toothed one...

Remixed multiple things here to get the set up I wanted on my Ender 3 V2 with the Black Knight linear rail kit using stock fans. Mini Satsana remixed to include endoscope mount. Adjust BL touch cover so fit within mount and cooling duct and...