camera mount swivel 3d models
428007 3d models found related to camera mount swivel.thingiverse
This is a modified Camera Mount Swivel for _Camera Arm - Standard Tripod Mount_ `Thing 3095730`. Link to thing: https://www.thingiverse.com/thing:3095730 I found the existing one had too large of a radius on one end. This is great for getting a...
thingiverse
This is a Swing Arm for a camera mount which I modified to remove unnecessary overhang which produced failed prints (See photos)
cults3d
I got this idea from seeing two different Raspberry Pi Camera things. I got the top part from: http://www.thingiverse.com/thing:442063 and the bottom from: http://www.thingiverse.com/thing:605368 Did a bit of editing and here it is. ...
thingiverse
I got this idea from seeing two different Raspberry Pi Camera things. I got the top part from: http://www.thingiverse.com/thing:442063 and the bottom from:http://www.thingiverse.com/thing:605368 Did a bit of editing and here it is. I did...
prusaprinters
And also to give a slightly better angle than just from the side.The camera holder itself is also tweaked slightly to support the camera being attached up side down if you want the cable to come from the top instead. The parts can be rotated how ever...
thingiverse
*Updated on request with screwdriver holes for configuring the IR sensitivity Did this remix of both designs referred to since i couldn't find a good camera holder that had support for the official Night vision camera. The arm is longer to support...
thingiverse
Check out my complete upgrade, the AM8 Dual Bowden here Mount a Raspberry Pi camera to your Anet A8 with this lightweight, easy to print camera mount. Tilts and Swivels. ...What you will need: 2x m2 14mm bolts and nuts Mount your Pi using my Ramps/Pi...
thingiverse
Voron 2.4 swivel camera mount, mounts on the 2020 extrusion before the doors. ... Use M3 mounting hardware.
thingiverse
Swivel camera mount. Uses 3/4" 6X32 machine screws. Hex nut snaps int the wing nut. Use super glue to hod firmly. ... Due to request, I added a 25,50,100 mm double ball.
thingiverse
Give your Simplisafe outdoor camera manual swivel/pan capability. Limited tilt provided by existing magnetic mount that is attached to swivel. STL files and Fusion 360 files included. Sliced files use CURA standard print settings for PETG, 0.4mm...
thingiverse
My cameras do not rotate side to side, so i made this and they work well for my house. Hope others find them useful too. You will need to insert a .250 Dowell pin after print is complete. ... Print Settings Printer: Monoprice...
thingiverse
A swivel tilt camera mount for D-Link WiFi cameras DCS-P6000 and DCS-8000. I designed it as an attachment for the Ender 3 and the mounting bracket fits the back side of the power supply and is attached using the two M4 screws. The mount could be...
thingiverse
Needed a web cam mount that was not restricted to only vertical up/down adjustments like the standard mount that comes with the Logitech C920 webcam. This is because I like to use two side by side monitors angled slightly. Thus mounting it on either...
thingiverse
Swiveling camera mount for the TAZ5. Print-in-Place base that slides onto aluminum bed tray, lock into position with a M3x5mm screw. Short (15mm) and Long (80mm) posts included... or find one from Thingiverse. Great for Octoprint! Keeps model...
thingiverse
So I decided to build my own that not only allowed me to mount such a camera, but also swivel it and also to mount it to the door of the 3D printer, so I could have a better front-on view and avoid the heat of the enclosed 3D printer. I always had...
thingiverse
2x M4 bolts 15mm needed 4040 and 4020 mounts added enjoy
thingiverse
I have designed a Swivel mount camera Arm/Holder for a TOP-301 IP Camera. http://www.banggood.com/720P-1_0MP-Mini-IP-Camera-ONVIF-2_8-12mm-Manual-Varifocal-Zoom-Lens-P2P-with-Bracket-Network-Camera-p-1047878.html Bolts used are M5 bolts,., see...
thingiverse
This is a 4 part camera mount designed to be rail mountable and more generic. ... It has a smaller camera mount surface for your webcam's claps to press into. ... It needs m5 screws/ nuts.
thingiverse
This is a camera mount for a Raspberry Pi camera (v2.1) and derivatives. May also fit the v1 cameras. I'm using it with a wide field of view camera (pictured, link:...
thingiverse
Allows easy modification of your AR Drone 2.0 forward-facing camera, to allow viewing angles from 90 straight up, to 90 straight down. Overenginerred design includes ~22 degree snap-to angles and ribbon cable guide. ...
cults3d
A front swiveling camera mount for Prusa i3 01-04-2015 UPDATED THE SUPPORT with the revision 2 and added the M6 Lever, refer to the picture for the lever installation Assembly videohttp://youtu.be/FqYquOGgjXg
thingiverse
A front swiveling camera mount for Prusa i3 01-04-2015 UPDATED THE SUPPORT with the revision 2 and added the M6 Lever, refer to the picture for the lever installation Assembly videohttp://youtu.be/FqYquOGgjXg Instructions Print all the parts at 0,3mm...
thingiverse
This is a swiveling camera mount for a Logitech C910. I removed the metal plate from the base of the camera, replacing it with this printed part and reusing the screws. It works just fine and I have no complaints in that regard. It's a bit clunky in...
thingiverse
This is my design of a mount accessory for attaching a GoPro camera to the print bed of my Anycubic Mega X. Since this printer has an i3 design, the bed moves, making it harder to get a decent time-lapse without Octoprint an a dedicated webcam. ...
youmagine
Actually being printed.Best result if printed with 0,3 layer and 35% infill3 perimeter suggested. ...Assembly video available here
thingiverse
I have remixed the mount for using camera without IR leds (see project https://www.thingiverse.com/thing:2873677)
thingiverse
Since unscrewing something everytime I have to open/close the front door I came up with a mount with an integrated hinge to swivel the mount and the camera away. ...The mount for the PS3 Eye camera that I have used is this one:...
prusaprinters
As I have also planned to add a acrylic front door it should be able to remove very quickly in order to open the door. Since unscrewing something everytime I have to open/close the front door I came up with a mount with an integrated hinge to swivel...
thingiverse
This is identical to http://www.thingiverse.com/thing:203968, but with non-manifold faces fixed. ... It sliced/printed just fine for me on the first try with the "fine" setting in Simplify3D on my MakerGear M2 printer, no need to rotate or change...