case enclosure 3d models
226509 3d models found related to case enclosure.grabcad
RileyLink 433MHz Case Enclosure for Omnipod Insulin pumpiPhone RileyLink Hard Case Original here :https://www.thingiverse.com/thing:3681759
thingiverse
Project case/enclosure for STM32 IOT discovery board (B-L475E-IOT01A1). It slides together after attaching board with (4) 4-40 screws or similar. The design allows access for the onboard sensors and also the Arduino expansion headers. The USB port...
thingiverse
This is a case/enclosure for a **TonUINO** that I am building as a christmas present for my 2 year old daughter. *Instructions available in german here: https://www.voss.earth/tonuino/* This enclosure has access to the SD-card, allowing me to swap...
cults3d
Description A secure case enclosure designed to fit iPad Mini 4th Gen tablets, featuring buttons for power and volume controls as well as cut outs for the charging port, home button and front facing camera (the rear camera is enclosed however a...
thingiverse
This is a case / enclosure for the very small and cheap DSO188 digital oscilloscope. It replaces the standard PCB case, offering more protection with minimal size increase. It reuses the 8 pcs supplied screws to mount the new case to the DSO188. ...
thingiverse
MKS Makerbase SKIPR basic case (enclosure) that uses a 120mm fan to keep it cool. The two halves of the case hold the board in place, and the 4 screws that bolt the two halves together hold the board in compression. You can use it with or without...
thingiverse
The temperatur inside the enclosure is much higher than room temperature, what is a great help for printing ABS (cause the layers have less temp difference => at least less warping, in my case I don't have warping anymore) It's easier to mount a...
prusaprinters
This is an enclosure for the Pixelblaze micro-controller. ... The screw holes fit at M2x7mm size screw.</p> <h3>Print instructions</h3><p>Lid prints best with the top down, I didn't require supports but you can enable them if needed.</p>
thingiverse
I've created a front case that has TRONXY on the front, as well as a case that is simply blank. This was created in SolidWorks, and the file can be provided upon request. I've seen a few cases for the Melzi board, but they are always snap-on fronts,...
youmagine
Case for the embedded development board Toradex Iris. ...Custom made in Blender for a customer (André Curvello) who kindly allowed it to be shared with a free license.
thingiverse
This case fits 3 rocker switches and 3 (5mm) power LED's The case also have two rectangles coming out from the side to be mounted on the k8200 with zipties Instructions You will need to either tape or do like i did, just put a little bit of hotglue...
thingiverse
This is a case which is housing one LNA4ALL and one LNA4HF low noise amp for the us with a RTL-SDR USB stick. ...More details on my blog:http://diebastelkammer.wordpress.com/ Instructions The details...
thingiverse
A case / enclosure for the very small and cheap FNIRSI-138 PRO digital oscilloscope. This case offers protection for the circuit boards with a minimal increase in size. The case is in two parts so that it can be printed with a non flexible filament.
thingiverse
... for the NooElec RF Upconverter v1.2. ...More datails on my blog:http://diebastelkammer.wordpress.com/ Instructions The two case parts are printed. ...Before assembly, the inner walls of the case should be covered with aluminium tape for RF shielding.
thingiverse
see: http://paulogeraldes.blogspot.com/2013/05/3d-printed-raspberry-pi-camera-case.html v0.1 - First version for a Raspberry Pi camera enclosure so as to prevent any damage to its exposed electronics from electrifying touches. In the top cases with...
thingiverse
Pick material based on the environment, but PLA/PETG should be ok (PETG recommended if you plan to put the screen into enclosed area/printer enclosure where temperatures may exceed 50 deg C). You will need some hardware to assemble the case - 4x...
thingiverse
Customized version of http://www.thingiverse.com/thing:1264391 This Arduino Uno + CNC Shield enclosure is for my Drawing Robot https://www.thingiverse.com/thing:2349232 This is a work in progress. ...
thingiverse
Enclosure for VESC 6 with strain relief,space for Bluetooth receiver and an arduino nano. Should provide some protection against impacts and water. M4 Screws are used for fixing the cables and closing the lid. ...A foam gasket could maybe be applied.
thingiverse
Here are some simple support structures to build your own enclosure. Buy some plexiglass (or take apart some poster frames) and connect them with these + some hot glue! ...Insulates the printer and protects from cats/children ;) ...
thingiverse
USB Meter Case to use with a simple and cheap 4 digit meter.
thingiverse
This is a case designed for the cheap DS0138 / DSO138 oscilloscope.
thingiverse
Couldnt find a nice case so i made one... Printable without supports! ... Needs some kind of rubber feet (5mm +-)
prusaprinters
Customized version of http://www.thingiverse.com/thing:1264391 This Arduino Uno + CNC Shield enclosure is for my Drawing Robot https://www.thingiverse.com/thing:2349232 This is a work in progress. Print Settings Printer: HyperCube Supports: No...
thingiverse
... is just an example of the acrylic cutout I used for my case. In reality, you can get any piece of acrylic that is larger than the window hole, but smaller than the case itself. ...Instructional Video Here:https://www.youtube.com/watch?v=mYnVwfppqzU
thingiverse
... Notes: No need for supports. High speed for the case should be ok, but the rear cover should be printed at much lower speed because of lots of retraction neccessarry for the little knobs!
thingiverse
A newer version of this design is here: https://www.thingiverse.com/thing:4183337 The microcontroller board easily slides into the case and can be enclosed by clipping on the included cap, leaving the USB-C port accessible while protecting the rest...
pinshape
... lid is optimized to snap into place perfectly, so there are no screws needed. ...However there is a lowered hole for a screw to attach the case somewhere. ... Printing settings: 0.3 mm layer hight 60 mm/s printing speed retraction ON
thingiverse
This is a case / enclosing for the QCoo Cube Developer Version (https://www.kickstarter.com/projects/788278700/qcoo-the-world-first-3d-snake-cube-with-ar-and-led), a cube with 150 RGB LEDs, Bluetooth LowEnergy, IMU (Gyro, Accel), Vibration Motor and...