cc by nc nd 3d models

### Design Details Key bucket is 85 by 85 mm with a wall of 3 mm. The rear wall is thicker and has a decorative key on top. The bottom is closed, so gunk will definitely accumulate but small and tiny keys will remain inside the bucket. There are...

I also made another version with the mounting screw offset by 40mm to mount the TUSH holder in the back of Platsa. This was needed because I have a few spools that are a little bit wider than the gap on the left of 'Ender would allow. ## Print...

If you need a version without spikes, you can resize the included cylinder in the slicer, move it in the hole, and remove the spikes by making the cylinder an infill mesh with wall count, infill, and top/bottom layer set to zero. Due to the way...

**License**: [CC BY-NC-SA 3.0](https://creativecommons.org/licenses/by-nc-sa/3.0/) HEAVY WORK IN PROGRESS I have the model sorted and am attaching it BUT it is not in a form that can be customized. So the STL attached for the north bearing is...

From The Bishop Permanent Collections License: CC BY-NC-ND 4.0 Learn more

##Design details I took the case from the "W1209 Temperature Control Switch" by Trierscheid and added the buttons from the "W1209 Thermostat Module Case" by 2Dprinter. These buttons are exactly where the screws should be. That means brass inserts...

Height of hooks is 3mm by default, image shows hook scaled in Z to 5mm. I recommend <i>hook2</i> because the other one is open and not very secure on the rail. Round part of hook has a diameter of 12mm. I will make a few more diameters in the...

Herb shade (roof, umbrella) for planting pot or garden. Two sizes: 288mm x 178mm (H x W) 224mm x 178mm (H x W) ## Why My parsley burnt in the sun so I needed a shade. Will update about parsley after a few weeks (Forgot to update but the...

Adjust position with the help of the mark or adjust by eye. Attach switch with 2x M2x15 to base. ###Modify GCode Modify the slicer settings by adding a command to drive to the right X limit position at the desired moment (e.g. the end of the...

Depending on print tolerances, the springs might hold in the holes by themselves. <li>Put <i>Spring Pad</i> into <i>Foot_spring_no pikes</i>. Make sure that the holes for the springs are pointing towards the springs. <li>Put assembled...

Foot to hold a broom handle (or wood stick) flat on a surface and prevents it from rolling away. Can be used to make a make-shift clothes bars. Athletic applications might also be possible but not tested. ## Why Needed a holder for a clothes...

Power plug case for Ender '3 power connectors (and similar) and a 23x15mm power switch for Ikea PLATSA cabinet. Might fit Besta as well but not tested. <a href='https://ko-fi.com/T6T4DXTSD' target='_blank'><img height='36'...

Part of a cupboard. I don't know where it goes or how it is installed. ## Why I friend gave it to me to make a few of these. Maybe someone can use this, too. It's probably something for a rail for the drawers or something. ## Design Details ...

Cn InfoYond東玖 | 原创模型 | CC BY-NC-ND-----------------------------------------------------------------------特别设计用于放置头戴式耳机，赛博风格+独特的夹持设计+优化过的“低耗材高强度”结构...

1/72nd scale German / British jerrycans (x20) For UV resin 3D printers. ... For personal use only (CC BY-NC-ND). ... For commercial use contact me first, please.

Ischnochiton yemenensis Van Belle & Wranik, 1991 BE-RBINS-INV-TYPES-MT-3657-Ischnochiton-yemenensis PARATYPE Copyright: RBINS / DIGIT-4 Belspo Licence: CC BY NC ND

1/72nd scale German (early) jerrycans (x20) For UV resin 3D printers. ... For personal use only (CC BY-NC-ND). ... For commercial use contact me first, please.

1/72nd scale JGSDF water cans (x20). ... For UV resin 3D printers. For personal use only (CC BY-NC-ND). ... For commercial use contact me first, please.

... Trapo. ... Creador: Impresión 3D México @impresion3d.mx Licencia: Creative Commons CC BY-NC-ND Si desea contactarnos, por favor visita: www.impresion3d.mx ------------------------------------------------------------------------- File: Muñeca de Trapo.

This model holds an: Attribution-NonCommercial-NoDerivs Licence CC BY-NC-ND This license only allows users to download the model and share it with others as long as "Stress Tech" name is mentioned when sharing. ...You can’t change this model in any way...

... and also be a sturdy platform for a funnel to fit. This a bayonet type fitment and has been successfully tested on a Mx5 and a Fiesta 1.0 ecoboost. I understand that NC and ND oil caps are interchangeable So this should fit a ND as well. ...

partitions made from 0.25" MDF. ...Plastic caps 3D printed. added version for NC

Non-Rolling filament spool stand. Ensures that the spools don't roll away when stored on a shelf. Intended as as simple stand <a href='https://ko-fi.com/T6T4DXTSD' target='_blank'><img height='36' style='border:0px;height:36px;'...

Mount for the Sensata Crydom SSR ED24D5R. ## Why I didn't want to buy a cheap Fotek knock-off SSR because I feared malfunction. Even if only 3.4A go into a Meanwell LRS-350-24, I'd rather be safe. I found this relay at the local electronics...

The present work will present the project developed for a 3d printer that aims to solve problems observed in Void3D's first generation machines, such as assembly difficulties, print quality and component lifetime.Using mgn9 for the motion system, and...

Broom stick attachment for a sponge holder. Makes cleaning a bathtub easier on the back. ## Why I wanted an easier way to clean the bath tub without having to bend down. I hope, this makes my back hurt less. For my personal taste, it's easier...

Instructions with pictures posted under same license on github here: https://github.com/jewzaam/pixel4-telescope-adapter The above repo is the source of truth. I have posted the STL from the repo as of January 10, 2021. ... I don't expect it to...

Spare leg (peg leg, wooden leg, peg-leg) for an office chair with 11mm / 50mm wheels. ## Why A wheel on my office chair broke and I needed a replacement until the new ones arrived. ## Design Details For a broken leg with about 38mm diameter...

Autors: Joan Font-Genís Àvila, per a ArsPicta/3DPatrimoni, dins el projecte finançat HAR2017-84451-P del Ministerio de Ciencia e Innovación del Gobierno de España. ...CC BY NC ND.

**1/72nd scale British 2 gal. ...POW cans (x24). For UV resin 3D printers. For personal use only (CC BY-NC-ND). ... For commercial use contact me first, please.