cell phone tripod adapter 3d models
194451 3d models found related to cell phone tripod adapter.cults3d
Custom Tripod mount for cell phone. This was made for my galaxy S6 with printed case to fit snug in the holder horizontally. Uses 10-32 screw and nut to hold bracket to base. ... 3/11/19 Added a threaded bottomed version to fit 1/4 20 SAE Thread.
thingiverse
Custom Tripod mount for cell phone. This was made for my galaxy S6 with printed case to fit snug in the holder horizontally. Uses 10-32 screw and nut to hold bracket to base. 3/11/19 Added a threaded bottomed version to fit 1/4 20 SAE...
thingiverse
Small adapter for 58 - 75mm wide phones. Large adapter for cellphones 70mm wide and wider. Print it with no support. 0.2 layer height. 25% infill 0.1 layer height for bolt and nut. 100% infill. Threads will be tight. I had to use wrench on nut...
thingiverse
This is a camera tripod adapter for a cell phone. It works well for my phone, an Avid 589, held in place by rubber bands (because of aging, use preferably silicon rubber, not latex), The trigger button on the phone is exposed and easy to...
thingiverse
This a remix of the tripod attachment point for Sergey_77's camera adapter. The thread in the original was the wrong size for my needs, so this is just a resizing to the 20-1/4 thread size needed for typical tripod posts found in the US, or at least...
cults3d
Tripod adapter for Pixel cell phone in Otter Box case
thingiverse
This adapter holds an acorn nut and then retains it with a little cover that can be secured in place with a couple drops of glue (if necessary). Fits the smaller Google Pixel phone using an Otter Box case. Printed on a PRINTinZ Flexible Printer...
cults3d
Tripod adapter for Galaxy s5 cell phone using Otterbox case
pinshape
This adapter allows you to mount your Galaxy phone with otterbox case onto a standard 1/4-20" tripod. ...You will need a 1/4-20 acorn nut to go in the square hole.
thingiverse
This adapter allows you to mount your Galaxy phone with otterbox case onto a standard 1/4-20" tripod. You will need a 1/4-20 acorn nut to go in the square hole. Shown as printed on a PRINTinZ flexible printer plate.
thingiverse
This is a replacement part for a cheap "Cell Phone Tripod Adapter Mount Holder Clamp" that came with a selfie stick. My kids selfie stick is missing in action but I still use the phone mount on my tripod. ... The mount broke so this is a replacement...
cults3d
The fully extended height is 95cm, 45cm retracted and 35cm by removing the piece that supports the cell phone. is 100% disassembled as it does not require glue or heat to fix the pieces. ... printing and assembly guide included in the compressed file.
thingiverse
The hole screen is free The buttons are free And for all cell phones I've ever seen, the camera is always on top so it's ok! You may need to open a cad and "push pull" some faces to fit your phone's size. ... ...
pinshape
The hole screen is free The buttons are free And for all cell phones I've ever seen, the camera is always on top so it's ok! You may need to open a cad and "push pull" some faces to fit your phone's size. ... Instructions filling 100% support material...
cults3d
... Wing Nut to assemble it. You can use an elastic to secure the phone to the mount if needed. There is two mounts.... ...one has a .45" opening the other a .50" Overall it worked very well for taking pictures of the northern light while on vacation.
thingiverse
This is a beefed up version of [ppet36 iPhone Tripod.](https://www.thingiverse.com/thing:1148654) I needed it to survive in a suitcase during vacation so I just redesigned it to have thicker legs, etc. I also uploaded separated pieces and rotated...
prusaprinters
This is a beefed up version of ppet36 iPhone Tripod. I needed it to survive in a suitcase during vacation so I just redesigned it to have thicker legs, etc. I also uploaded separated pieces and rotated them to lay flat for ease of printing and...
thingiverse
Simple OpenScad parameteric design with captured 1/4-20 nut Designed last minute before going on a vacation Just measure the max width of the phone in portrait position(pictured) or landscape and change the "length" variable also Measure the max...
prusaprinters
I browsed around the internet and like this design https://www.thingiverse.com/thing:25098 and just made some small changes. For reference, my phone is an iPhone 11 in a Speck Presidio 2 GRIP case. I would assume the mount would work other phones in...
thingiverse
Cell Phone Tripod Mounting Plate 58.5x59.5x11.2 Print Settings Printer: Home Made Rafts: No Supports: No Resolution: 0.2mm Infill: 25%
cults3d
Mechanism made up of 6 pieces that allow a universal cell phone support to be attached to a conventional tripod and allow for a combined movement of 3 degrees of freedom, easily adjusting to any size of cell phone. ...Easy printing and removal of...
thingiverse
I wanted to do a hyperlapse of printing but I needed a cell phone mount for my tripod so here's the end result which seems to work really well. I designed it to fit a phone as small as a gen 4 iPhone or as large as a LG Turbo in a beefy case. ...
thingiverse
I needed a mount for my cell phone for the teleprompter that was made by https://www.thingiverse.com/dsft which is linked here https://www.thingiverse.com/thing:2978080 I found a few but they all required that I have a rubberband wrapped around the...
thingiverse
I used these to attach my phone to the holder (shown in images above): * holder to tripod (hot shoe adapter): https://www.aliexpress.com/item/4000538932126.html * tripod to phone (cell phone tripod adapter):...
thingiverse
I created a pocket sized "tripod" for use with a cell phone. The swivel has a cutout that fits my Pixel 5 and the screw helps clamp the swivel in place at your desired phone angle. A cutout for a Velcro cable strap is provided as well if you have...
prusaprinters
I created a pocket sized "tripod" for use with a cell phone. The swivel has a cutout that fits my Pixel 5 and the screw helps clamp the swivel in place at your desired phone angle. A cutout for a Velcro cable strap is provided as well if you have the...
grabcad
This project started cause I did not want to hold my cell phone by hand recording Class lectures and so it evolved into an ajustable cell phone mount. I have printed this item out on a 3D printer and it works great. Hardware such as nuts and all...
thingiverse
It'll hold a phone as small as an iPhone 5 or SE with no case and as big as an iPhone 6 with a thin case. You'll also want to be sure not to over tighten the plastic bolt. You have more than enough strength to shear it off. ... You will need to add a...
thingiverse
This is an adjustable tripod mount for your cell phone. It will hold an old small ipod touch, and a really big phone too (not a tablet). There are 3 parts to print, and this is not a super easy print. You will have to manipulate g-codes a bit to...