chain motor 3d models

1 Ton Chain Motor often used in Entertainment Rigging

X-Chain Motor Mount Reinforced with extension for Cams, tools, wires....

... I couldn't use the old mount on the carriage side anymore. ...Therefore I designed a compatible new one, that slides over the backside of the extruder motor. The chain with which it works is: https://www.thingiverse.com/thing:1735193

... I couldn't use the old mount on the carriage side anymore. ...Therefore I designed a compatible new one, that slides over the backside of the extruder motor.

This is a stage rigging chain motor based on a CM 1 ton. ... Add chain and lobster clasps and you are set.

Remixed cable chain motor mount from scratch specifically for the Elegoo Neptune 3 printer, though it would probably work for other Ender 3 clone printers as well. The size of the motor that this fits is 42.3mm x 42.3mm wide/long so you can check...

I used AnthonyB's fantastic and simple Nema23 stepper motor clamp and shrunk it a bit to fit the Nema17. Use Nylon or PETG, ABS should work too. ... Fit may vary.

Bucket Chain drive Motor with Air to Air Cooler for top tumbler

Standard 7x7 cable chain mount on motor side, with sockets for endstops and z-probe connectors.

Wanted a way to connect wire chain cleanly on my I3 Einstein rework x axis. ... Attaches to extruder motor

I saw the need to reverse the cable chain so it stayed with in the footprint of the printer, The general concept originally was great I just can not leave well enough alone so here is my Rework and reverse Cable chain for the X-Axis on Anet A8...

Reworked motor mount for latest x carriage

The original Motor Anschluss was always falling from my motor, so i've made the front wall higher. It is not falling anymore. ...Also, i've deleted the rear logo.

This is a Remix of https://www.thingiverse.com/thing:2920060 and https://www.thingiverse.com/thing:3769941. ... There is no need for screws, the mount just snaps to the extruder motor.

... is realy good design for Anet a8 printers. But if you use the autolevel device with inductive sensor, we don't need z end-stop support on the Cable Chain X Motor Mount. I design a mount without the support. ... Thanks for comments and likes :)

... chain is realy good design for Anet a8 printers. But if you use the autolevel device with inductive sensor, we don't need z end-stop support on the Cable Chain X Motor Mount. I design a mount without the support. ... Thanks for comments and likes :)

Gear output chain for 80cc bicycle motor kit. ...Material 1045 or 1050 steel.

I also printed using PETG to provide a little more heat resistance to the print since it will be sitting on the hot stepper motor. ...Very little testing has been done to see how long it will survive but I am hopeful it won't suffer any deformation due...

... on. Spent hours looking for a suitable X-Motor mounting bracket for a cable chain suitable for my Prusa-i3 clone. Yet as my unit has a strengthened bracket already, any designs out there wouldn't fit over / onto it. ...So had to design my own.

Actually a remix of https://www.thingiverse.com/thing:4790857 which is a remix of the original https://www.thingiverse.com/thing:3769941 for a cable chain mount for the Creality Ender 3 Pro (mine was purchased 11/2021). The remix has slightly...

This is the Chain to Motor mount only, and was 99% originally designed from creator: NG_Design. This a minor adjustment to the motor mount because mine slipped off twice. Changes: - taller corner grips - slightly longer extrusion of snap tab I...

If you printed this https://www.thingiverse.com/thing:3769941 and it doesn't fit your ender v2 so well and tends to fall of, you should have printed this https://www.thingiverse.com/thing:4790857/comments instead. ... As i didn't want to waste...

This is a remix of the Logitech C270 Mount for the Prusa i3 MK3/MK3S, https://www.thingiverse.com/thing:3272618 by SethBon combined and remixed with the Prusa i3 MK3 Cable Chain Add-on (ALL AXIS), https://www.thingiverse.com/thing:2862375 by llj3663....

I am also working on cable chains with loose enough tolerances to not induce friction/drag on the print head while still being stiff enough not to sag down toward the print-bed. These will also be included once I get the update published. Keep...

Small cable holder can be used for fixing cable between motor and round 4-pin connector. ...YES - you need washer on both sides (between #608 andholder and so between the screw head and holder) Print Settings Printer: Geetech...

This mates withhttp://www.thingiverse.com/thing:40918 orhttp://www.thingiverse.com/thing:11978 The chain sticks out on the left side of the bot and the connector is on the front. Mine will have the mating plug/socket with the cable pointing up. ...

for 3018 pro + with Z in aluminium the rest of the string on the file https://www.thingiverse.com/thing:4738582 perfect thanks

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/cBFnPyMBUYe

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive.thIt is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002and some Nema17 motor chain mount I...

... be using version C. This mates withthingiverse.com/thing:40918 orthingiverse.com/thing:11978 The chain sticks out on the left side of the bot and the connector is on the front. Mine will have the mating plug/socket with the cable pointing up. ...