chameleon 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

... The COMPLETE Sunken Kingdoms I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Tritons are the proud folk of the seas, which ancestors are common to those of the Alfar.

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

... THANKS! Happy printing! PS.: Thanks to Rick and Morty, who posted this wonderful ASX1 model on grabcad, which I used as the basis for my renders (and my apologies for the poor quality photos - my printer stands in a pretty dark corner of the room).

I made a slight modification to the model by changing the profile of the USB input so the bridge was less than 5mm (was almost 10mm) and changed the way the board mounts so the top has all socket heads and no washers (just an aesthetic thing). <a...

The COMPLETE Maneater Nagarots I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Nagarots are a cult devoted to the Serpent Demon Yn'aga, herald of the Tyrant-God...

Here you find better resolution for the pictures: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa https://www.youtube.com/watch?v=5lFdzL06OOs On Youtube there are lots of tutorials to build a 32x32...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aeraunder...

2)The plastic for the case is about 0.5 kg (the lantern is large, it was made for a large candle) 3)2 hinges for caskets 15x21mm with self-tapping screws (included, sold on marketplaces) 4)a handle for the casket (you can print it, but I wanted...

I made 2 cover models: one is you can do multiple color layeur prints and one if you can't. The multiple color files are noted CoverBox2_colorX and the single color STL is CoverBox1.&nbsp;</p><p>If you're using multiple color layer prints, the height...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

This is a remix of my previous models: [Modular Wahoo Board Remix](https://www.thingiverse.com/thing:4207631) [Modular Wahoo Board Remix Case](https://www.thingiverse.com/thing:4302373) In this new version, I have opted for a singular base with...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

This is a rather dramatic redesign and requires your printer to be able to comfortably print 55 degree overhangs though I would recommend facing the top of the model toward your fans for more efficient cooling of these overhangs. Please also note...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Just drag the lithophane (standing up) to the mount, and position it so that it intersects the model, while lining up the curved edges as seen in the picture. 3. While that is printing, disassemble the nightlight by pulling off the diffuser,...

The COMPLETE Bonegnasher Gnolls I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Gnolls were spawned by the Demon Raz'n'guul, born from a rotten tooth of the corruption god...

The COMPLETE Dumlok Flameseekers bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: 12 Dumlok Flameseeker (modular figures + figures with helmet)The Dumlok,...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

... I'd use WS2811, 12V strips in either 60 LED's per meter or 96 LED's per meter. For arches the 60 LED / meter is probably the sweet spot. Feel free to suggest improvements in the comments section. ToDo: Create xLights model and add to download.

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

You could group them in Tinker and make a single/twin mega model - love that Tinker feature! Support is required in places due to geometry, but it's very simple square profile support that is easily removed. I always try to avoid it, but not at the...