clip retainer for power plug 3d models

Since it doesn't have a clip or a catch, i thought to make a small retainer clip that fits snuggly to keep it from sliding out.If you liked this thing enough (and was hopefully useful!), please consider supporting me via Paypal in doing more stuff...

Simple balance plug retainer for both 4s and 6s balance plugs. Attaches to battery strap up to 21mm wide. Keeps everything nice and neat. ... Print in TPU @ 20%

print standing up as this ensures that better strength as compared to laying down for the small clip feature. I did change the design slightly, i.e. more clearances etc as i couldnt get the original to fit into my laptop. Also i added slight...

... fall out. ...Since we don't use the USB ports much and there's 2 next to the power port, I modified @flintols USB plug to have a clip to help hold the power cable in position. ... To be useful for others, you'd need a USB port near to the power port!

... fall out. ...Since we don't use the USB ports much and there's 2 next to the power port, I modified @flintols USB plug to have a clip to help hold the power cable in position. ... To be useful for others, you'd need a USB port near to the power port!

Since we don't use the USB ports much and there's 2 next to the power port, I modified @flintols USB plug to have a clip to help hold the power cable in position. To be useful for others, you'd need a USB port near to the power port! Print Settings...

This is a clip or type of retainer that keeps auditorium seats in place. ...I don't know what model or type these seats are, and because they were old we had no parts for them.

This is a retainer clip that holds a piece of glass or a mirror in an inset. Instructions Scale on z to fit inset. Use a hot glue gun to fill gap FROM BOTTOM to get niice pillow. The drop of hot...

10 year old Fiskar pruning shears, retaining clip (to keep it closed) broke. Needed a replacement part. ...Tinkercad to the rescue.

This is a clip for a Laguiole knife as I was worried the knife would slip out of my bag/pocket if i'm not careful. The clip is designed to remain in the bag and the knife is pulled out from it. ... Print sideways for layer strength.

To install the bracket, first insert the power plug, then the bracket over the plug and around the DB9 connector, and then the DB9 handset plug. Tighten both thumbscrews of the handset plug to lock them in place. I used 6 small washers under the...

Phantom 3 - Battery Charging Hub Power retainer clip. I bought this great DJI Phantom 3 Professional and I also bought the charging hub. The issue is the clip that connect the hub to the power brick has no mechanism to lock it in place. It slides off...

This is Retainer Clip for old eletronics gears like cassette or VCR .

Ths is the clip to replace the retaining clip if you have LED replacement drop in lights for the turn signals likeI have for my BMW 1200 gs. Mine are the Weiser branded ones, they work great! ...Print Settings Printer Brand: ...

This is a plug shroud for a power strip cord that I made to keep the cord from being pulled out of the wall.

...... Please note that it is tweaked for my printer and especially the length of the legs might need adjusting. It's a quick print so just try it out and see if it fits. v3 version has better stability in the sides and bigger hooks to latch on better.

Just a slide clip for the handle to keep closed for a bag clip https://www.thingiverse.com/thing:3238736

The handle on my cheap can crusher won't stay up, so I printed a clip to keep it upright. I printed in PETG as it is outside in the elements. ... Use it as-is or remix it to fit your needs.

:-) This is a small clip used to hold down the cable that comes out from the floor in The Replicator and goes up to the heated bed. Instructions Created in Sketchup. I printed on my Replicator with...

Actually, the original MKS Gen L box placed inside the base frame doesn't allow the use of the power supply plug with this last. ... The plug can be provided from here:...

Using the wall mount designed by steve5092 the cable of the hairdryer is dangling to the floor and tangling itself. Double tape this holder next to your outlet to avoid this mess :-)The holder is slightly angled upwards, so the plug wont fall...

Using the wall mount designed by steve5092 the cable of the hairdryer is dangling to the floor and tangling itself. Double tape this holder next to your outlet to avoid this mess :-)The holder is slightly angled upwards, so the plug wont fall...

... tilted to block the sun. ...designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. ...Thanks, Enjoy!

... to block the sun. ... designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. Thanks, Enjoy! ...

This is a power plug adapter for the Byrne power unit power strip(the Byrne Axil X) the plug we are using is the Leviton square 1374 snap-in receptacle. Last I checked these were 12$ bucks on Amazon. This is way to high, don’t buy these. We found...

Plug for packaging food. Hard, not cracking - simple. ... Easy for print ;) For Ultra PLA: Layer: 0,2 Support: No Infill: 20% Walls: 1,6mm Temp: 210 Build Plate: 60 Colling: 100%

I made a flip top table for power tools, but there was no way of securing the cables. ...Made these simple retainers and clips for the cable ends.

This is an add-on for https://www.prusaprinters.org/prints/1735-toyota-oem-style-trailer-hitch-cover-plug/comments#comment-106509I sized it up close, but the intent was just to drill a couple holes and use a zip-tie. ...PEGT, 0.20 mm, 100% infil</p>

Think of it as a jock strap for a heavy cord ;-) Print two Angle_Bracket_03, tap them M3 and attach them to Backbone_04 with flat head screws. After replacing the original with the new Cover_Plate_05, slide the Backbone's nubs thru the keyhole slots...

This is a power cable retainer for a Dell Precision 75XX series laptop, specifically tested with a 7520. It is annoying that the power cable will fall out all the time if you move the laptop. This will keep it in the laptop by clipping into the...