colido 3d models
218 3d models found related to colido.thingiverse
A disk to guide the filament into the Colido Compact printer.
thingiverse
ColiDo diy Printer upgrade. ...Aluminum heat plate with 12V 200W IP65 Waterproof Flexible Silicone Heating Pad Heated Pad.
thingiverse
Adapter for the CoLiDo reel to fit Malyan M180. Design was from someone else but the part scaling was all wrong so I re drew it in Solid Works. ...Can't find the original link but when I come across it again, will add the link.
thingiverse
scale up 10 times to get the right measurements it should be 2mm thick Print Settings Printer: colido Rafts: No Supports: No Resolution: 0.1 mm Infill: 100%
thingiverse
*** IMPORTANT NOTE: *** The PrintRite CoLiDo DIY 3D printer does not support an ABL sensor out of the box. In order to make this work, I had to completely retrofit the machine's electrical system with a board that supports a z-probe (RAMPS 1.4 in my...
thingiverse
Original Colido motherboard is too slow to engrave very fast, I upgraded to an ATMega 2560 with RAMPS1.4 and have since enjoyed cutting vinyl, leather, wood, and plastic. Engrave glass by cutting vinyl mask and using etch cream. ...Engrave metal by...
thingiverse
I got tired of the stock Colido 3D DIY spool holder, so I created this one. I know it's ugly, but version 1 was even uglier, believe it or not. It works better than I had hoped for and has made filament changes a breeze! Plus the feed mechanics...
thingiverse
het nieuwe model voor de CoLiDo DIY HD kit van 123-3d.nl heeft een snap fit bodem, de mogelijkheid om knopjes toe te voegen is er.
thingiverse
Hallo this is a z axis mechanic for Colido DIY because my broke. I juse.IGUS RJ4JP-01-08 drylin bearings. ...The bearings a littel bit longer than the orginal, so i have more stability and no wobbeling if the z axis is going up and down.
thingiverse
So I scavenged a Flashforge Creator (I think it is a Replicator Dual clone) and a couple of cassette-like filament spools (branded Colido and QiLive, I do not know if those things are standard or not...) and I thought it would be a good idea to...
thingiverse
There are a number of Z Stabilisers available out there for the CoLiDo DIY 3d Printer. This is my version and is customisable should you run into Z travel issues. I've found that my z rods are not uniform and so I need a slightly different size...
thingiverse
This is a very basic thing - A calibration pillar to replace the awkward calibration card that comes with the Colido/Printrite DIY 3D Printer. Print 2 of these then stand them up on their ends next to the two Z screw rods and level off the platform...
thingiverse
... required, just buy the 4 quid "tyre gauge" bolt it in place without modification and with some 2mm bolts and presto your away..... simples Print Settings Printer: Colido Printrite diy 3d printer Rafts: No Supports: No Resolution: .3 Infill: 30%
thingiverse
The Colido 2.0 is a nice machine but it doesn't have effective cooling (not my model anyway). There is an existing fan that cools the mounting bar via a heat sink, the motor somewhat and the electronics by air exiting the heat sink leftwards but most...
thingiverse
I have the Colido 2.0+ 3D printer and had some issues where the plastic would warp because it didn't cool quickly enough, so I made this snap-on cooling fan inspired by https://www.thingiverse.com/thing:1710023. The difference in print quality is...
thingiverse
Box for my 3d printer used plexiglass for the windows and only costed 45 bucks.
thingiverse
THIS IS A SPOOL HOLDER IN WHICH CAN BE INSERTED INTO THE CENTER HOLE OF THE EXISTING SPOOL HOLDER. THIS ALLOWS THE USER TO QUICKLY ADD A SPOOL OR ANY EXCESS FILAMENT IN ORDER TO KEEP ORGANIZED. SUPPORT IS ALREADY BUILT IN AND IS BREAKAWAY, BUT A...
thingiverse
Fan layer mount for 50mm radial fan and new TOP por support all thing. ... Good prints you guys!
myminifactory
THIS IS A SPOOL HOLDER IN WHICH CAN BE INSERTED INTO THE CENTER HOLE OF THE EXISTING SPOOL HOLDER. THIS ALLOWS THE USER TO QUICKLY ADD A SPOOL OR ANY EXCESS FILAMENT IN ORDER TO KEEP ORGANIZED. SUPPORT IS ALREADY BUILT IN AND IS BREAKAWAY, BUT A...
myminifactory
Box for my 3d printer used plexiglass for the windows and only costed 45 bucks. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:735213 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=735213 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:3455976 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3455976
thingiverse
Customized version of https://www.thingiverse.com/thing:3455976 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3455976
thingiverse
Nozzle fan for the printer family COLIDO 1.0 / 2.0 / 3.0 / M2020 / X3045 Thiner than using a 40mmx40mm fan