corsair mesh front panel 3d models

Decided I wanted to make my own woodgrain front panel for my Corsair 4000D, in the spirit of the Fractal North. I've included the CAD file as well so you can make whatever changes you want and adapt your own front panel design. Might need to rotate...

I always wanted a honeycomb pattern on my front panel, but by the time I got a new case I couldn't find any models with one. Then I got a 3D printer. Instructions: 1. Set top & bottom layers to 0 2. Set a decent number of walls (3 was fine in my...

I always wanted a honeycomb pattern on my front panel, but by the time I got a new case I couldn't find any models with one. Then I got a 3D printer. Instructions: Set top & bottom layers to 0 Set a decent number of walls (3 was fine in my case)...

Made to impove the airflow through restricted PC case front panels. I made these for a Case Upgrade Video on my YouTube Channel "PXL Generator" Watch it here. ... English - https://www.youtube.com/watch?v=B4DF482Tvio Deutsch -...

Corsair 5000D/X Front Top panel

vibration dampers for the front panel of the corsair 275R, under certain conditions it vibrated in low frequencies, adding these fixed the issue for me. They print out quickly, and you can fill them with anything heavy, I used plaster. ... Used a 0.4mm...

Hello, Following a defect of my panel of fixing of face. A fixing lug was broken. I drew and printed the fixing tab in order to repair it. ... Sincerely

An "open-airflow" hexagon-mesh front panel for the 011 Dynamic (non-XL) Printed in two parts, glued, and painted. ... Requires: 2x M3 screws, for top attachment 300x300mm print bed, for large parts CA Glue or epoxy, for assembly

**Mesh front panel for Cooler Master MB530P computer case. ...It's magnetically attached and doesn't require any permanent case modification.** ##### Parts required: ##### - 4 screws to hold to the magnets - I used Flat head M3x5mm hard drive mounting...

- Please consider sending DryFly a tip as well!** **UPDATE 2: If you want to add your own mesh pattern or design, here is a solid version on TinkerCad: https://www.tinkercad.com/things/3liiNYPmccR-solid-icue-4000-airflow-front-panel** I have a...

Custom Elite Dangerous version of my Corsair iCUE 4000X Front Panel design showing the 3 base Elite badges, Combat, Exploration and Trading (from top to bottom) This will fit the Corsair iCUE 4000X & 4000D cases as they are the same chassis. If...

I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.

Custom Elite Dangerous version of my [Corsair iCUE 4000X Front Panel design](https://www.thingiverse.com/thing:4889085) showing the 3 base Elite badges, Combat, Exploration and Trading (from top to bottom) This will fit the Corsair iCUE 4000X &...

Designed a new front panel for my Corsiar computer case to improve airflow. My CPU (Ryzen 5 3600) and GPU (AMD RX480) each run about 10 F degrees cooler and the blower style GPU is runs much more quietly.</p> <p>It is designed to be printed in 3...

Designed a new front panel for my Corsiar computer case to improve airflow. My CPU (Ryzen 5 3600) and GPU (AMD RX480) each run about 10 F degrees cooler and the blower style GPU is runs much more quietly. It is designed to be printed in 3 pieces...

Mesh front panel for the Corsair 350D. Use support for the hooks. Size 288x178x13mm. ... *15.09.2020 added a new Design.

With certain fans placed in the new Corsair 4000D cases (I have the airflow and have Noctua NF-P12 redux-1700 fans, but I assume it happens with the non-airflow as well), sometimes the front mesh panel can contact the center fan's centerpiece and...

This is a mesh dust filter for the Cooler Master MB530P front panel to go with the great mesh front panel created by eBoB_ (link: https://www.thingiverse.com/thing:4828680 ). It's made up of .8mm square holes for decent dust filtration without...

My case Corsair x465 had a mesh on top which I had to remove because of thermal throttles. The Top however looks quite ugly. So I created this custom "mesh" (more like design.) It has these "trenches" in case you have AIO screws at the top. It...

As pointed out by Gamer's Nexus the front panel mesh is great for catching large debris but Lian Li left a large open slot at the bottom handle that allows air intrusion with no filtering at all and blocking that intrusion doesn't negative impact...

As pointed out by Gamer's Nexus the front panel mesh is great for catching large debris but Lian Li left a large open slot at the bottom handle that allows air intrusion with no filtering at all and blocking that intrusion doesn't negative impact...

Just a custom Front for a Corsair 900D.

Instrument panel designed for 1/5 scale Corsair. ...The instrument panel is designed according to blueprints.

mesh panel

Front cover for a Corsair 250D Mini ITX computer case, thin aluminium panel glued to a molded plastic mount. Rule and vernier used, so it should be relatively accurate... ...the rest of the 250D will be uploaded in sections as completed.

This is a FRONT foot for the Corsair K70 keyboard. The K70 has both front and back feet. The two front feet are identical while the back have a different left and right. I did not try printing this yet myself, but modeled it by request to get some...

This is a FRONT foot for the Corsair K70 keyboard. The K70 has both front and back feet. The two front feet are identical while the back have a different left and right. I did not try printing this yet myself, but modeled it by request to get some...

Remixed to improve printability and strength (the "head" would easily snap off from the stem on the original in my prints)

In an improvement over the stock panel, I wanted to make it easier to remove the panel to get to the dust filter so I also redesigned the clips that go into the chassis and am using magnets to keep everything connected. The files include a split...

Spacer for Corsair 570x Glass side panel