coupling nut 3d models

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Druidic missionary of Renmaeth who heard the tale of the Anshani Empire in Edrador. Wishing to steer them from their industrious ways, Myrion travelled to the far away...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

... THANKS! Happy printing! PS.: Thanks to Rick and Morty, who posted this wonderful ASX1 model on grabcad, which I used as the basis for my renders (and my apologies for the poor quality photos - my printer stands in a pretty dark corner of the room).

One suggestion offered is to quickly wave fire under the problem area in the hopes that the hair will burn away before the plastic is damage, but I came up with a different solution.This set of models replaces the entire front wheel assembly. The...

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

Most LEDLB, LEDP10W and LED10W series lights ship with mating connector as part of a harness or pigtail, depending on the model. Some larger LED lights like the LEDLB-160X2 or LEDLB-200X2 or multiple function LED lights (i.e. ...high/low beam,...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

There's the distance between the pin latches and the depth of the back cover recess defined by the svg, and then extrude the profile using whatever modeling software will accept an svg to the width of the pins. I personally used Inkscape and FreeCAD,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Cap for benq projector lenses, designed for the mx660 model. It fits perfectly. On the outside it has the logo of benq and on the inside that of ho-kago tea time (musical group from the anime k-on). This projector did not have the cover when I took...

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

The sourced parts needed are the same than for a MyRCCar OBTS Chassis, so you can use them in all models by now. This means that you can reuse existing parts from other projects, making it easier and more cost-effective to build this chassis. If i...

The models in my pictures were printed in beige ABS, which is a standard 1.75 mm filament from XYZ manufacturer. I have not tested other filament materials with this design. If printing as a fake sprinkler, I would recommend choosing black; bright...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos and...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

Since my first published keybboard was The1987 (https://www.printables.com/model/299777-the1987-a-modular-retro-inspired-87-key-mechanical) and it's fairly popular, and its designed around the Phantom circuit board and Teensy 2.0, which are no longer...

for the Firebrigade, working at hightSimilar thing on picture https://www.thingiverse.com/thing:6500617The most important mounting hardware used:-2mm dia tooth picks-3.2mm dia Mikado game sticks.-3.5mm metal screws for plastic (no machine screws!)The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...