cr 10 mini 3d models
410862 3d models found related to cr 10 mini.youmagine
Ho realizzato per la mia cr-10 mini questo supporto per rendere più facile l'inserimento della micro sd tramite una proluga.
myminifactory
guide filament pour CR-10 Mini PLA 0.2 / 15% imprimé sans supports
thingiverse
Easy turn knob fits over existing knob on CR-10 Mini to make it easier and faster to change settings, especially setting nozzle temperature. Use outer edge of knob for fine settings. Use knob crank handle for coarse settings. Add supports to just...
thingiverse
I remixed the lack table legs for my Creality CR-10 Mini
thingiverse
A way to test how well your CR-10 Mini bed is level. ...Just print & evaluate.
thingiverse
CR-10 mini bed level test. Slice with 0.25mm layer height. ...That will make it one layer even.
thingiverse
I could not find a handle for the CR-10 mini so i made this one, Print it just the way it is. ...Enjoy
thingiverse
A simple print to test the bed leveling. ...Sized for CR-10 Mini (220x300). ...Make sure you enable the "Print Thin Walls" in CURA.
thingiverse
CR-10 Mini Control Box Support. Mount your Control Box to your frame. ...Simplest way to make an all-in-one.
thingiverse
A stand for the glass bed on the CR 10 Mini. I use it to cool the glass quicker so I can go back to printing. =) I have it mounted on top of my enclosure with double sided tape. ...
prusaprinters
... not find a handle for the CR-10 mini so i made this one, Print it just the way it is. ...Enjoy Print Settings Printer: CR-10 Mini Rafts: No Supports: Yes Resolution: .2 Infill: 50 Filament: Filament Friday PLA Red Category: 3D Printer Accessories
thingiverse
This is a Prusa Slicer 2.3.1 profile tweaked for best quality in Creality CR-10 Mini. It should be compatible with CR-10 and Ender 3. Instructions: 1. In Prusa slicer select File => Import => Import Config Bundle. Select the file...
thingiverse
This enclosure for the CR-10 Mini has all the parts you need except screws and plastic walls as well ass two or three LACK table from IKEA. It has also a little door at the side to make it easier to change filament. ... Total height inside is 53 cm or...
thingiverse
CR-10 mini filament holder extender The original part was not long enough for all of my filaments, so I made an extender. After the print I've made some changes and upload here the new version (with a flange at the end). ... I use sketchup for...
thingiverse
I made 2 versions, with and without text (CR-10 mini) in case somebody wants to use it on another type of printer In the back, I added 2 studs that fit in the rail of the frame, makes it a bit easier to mount horizontally by using the spare nuts and...
thingiverse
This is a Creality CR-10 Mini Z limit switch mount laser cut file created with Inkscape. I cut the part out of red cast acrylic on a K40 laser using the K40 whisperer program. The holes are tapped M3. It was the first time I used the K40...
thingiverse
Searching for an enclosure for my CR-10 Mini to print PET-G and ABS, I came across this: https://www.thingiverse.com/thing:2864118 A beautiful and simple solution, but it won't work for my CR-10 Mini because it was too short. I decided to make a few...
thingiverse
This part provides strain relief to the connector of the CR-10 Mini heat bed. Previous designs of strain reliefs for the larger CR-10 models are incorrect for the Mini, including the STLs that are on the SD card shipped with the printer. Print: ...
thingiverse
Materials needed: 2 x 3D printed clips 1 x short length of 8mm smooth or threaded rod 2 x 608 ball bearings This is a quick and effective ball bearing spool holder for the CR-10 and CR-10 mini. It uses an 8mm smooth or threaded rod, and two 608...
thingiverse
I was looking for a mount for my Logitech C920 on my CR-10 Mini. I couldn't find anything that worked with my printer placement. Most stuck out too far, or vibrated too bad during the print. This is a pretty generic thing, but it worked well for me...
myminifactory
So i added them (the ones with 4 holes) This is a leg for my CR-10 Mini, so you can put the Control-Box under the Printer. It mounts screwless into the Aluminium-Profile and you also do not have to remove the original Feets. Maybe, when you have a...
prusaprinters
So i added them (the ones with 4 holes) This is a leg for my CR-10 Mini, so you can put the Control-Box under the Printer. ...It mounts screwless into the Aluminium-Profile and you also do not have to remove the original Feets. Maybe, when you have a...
thingiverse
So i added them (the ones with 4 holes) This is a leg for my CR-10 Mini, so you can put the Control-Box under the Printer. It mounts screwless into the Aluminium-Profile and you also do not have to remove the original Feets. Maybe, when you have a...
thingiverse
CR-10 Mini Z-Axis brace brackets, will probably fit others in the CR-10/Ender lines with some threaded rod length changes. The upper bracket is long enough so the brace will clear the print head assembly and a BLTouch bed probe when the head is all...
thingiverse
All for a CR-10 Mini but just increase screw lengths for CR-10. I used a new 500mm screw (T8*8) but re-using the original I needed to add a bit to get full travel, see txt file. May be worth buying 2 new screws to save messing about. My basic...
thingiverse
Cool looking knob. ...Useful to push filament into the extruder. (CR-10)
thingiverse
AIO Mini CR-10 Control Box ===================== ###ALL IN ONE CONTROL BOX I didn't like the CR-10 control box so I made an all in one box out of a mix of wood and 3d printed parts. I have a CNC machine so I used the box gadget in Vcarve Pro to...
thingiverse
I made a special leveling knob addition for my CR-10. I have figured out the main problem in my case was the loosening screws (leveling knobs) while printing. ...Since I have blocked the knobs with this fixture I am printing more than 100 hours with no...