cr 10s bed leveling 3d models

Creality CR-10S bed leveling knobs for a SainSmart reprap purchased February, 2018. Other knobs were slightly off, so I created these using Fusion 360 and test printed them several times until the fit was perfect (for my printer at least). The...

Creality Cr-10S bed leveling video Enjoy the Videohttps://youtu.be/MvaqixoxPLU Twitter:https://twitter.com/Zep_To_ Facebook:https://www.facebook.com/ZepTo.3D.Druck Google+https://plus.google.com/u/0/109561398985315771625/posts...

Creality Cr-10S bed leveling video Enjoy the Video https://youtu.be/MvaqixoxPLU Twitter: https://twitter.com/Zep_To_ Facebook: https://www.facebook.com/ZepTo.3D.Druck Google+ https://plus.google.com/u/0/109561398985315771625/posts YouTube...

Hello, here is my Bed Leveling Knob I use for my CR-10S. I printed mine in ABS with 3 Shells, 6 Top/Bottom, 25% Grid Infill with my Tarantula... Don't need supports And I forgot to mark the top of the number's with Black Marker... ... Have a...

It is hard to get a large bed that is 100% level because of the bed warping - it is recommended to focus on the leveling of your print region instead of the entire bed. It is also recommended to install a Automatic Bed Leveler, and use this test to...

Inspired by orcusomega's "Locking CR10/S4/S5 Bed Leveling Knob" (https://www.thingiverse.com/thing:2462249). This is a knob that you can insert an M4 lock nut into. The hole for the screw is not fully open. After printing there is a .4mm layer that...

Replacement of springs, permanent bed mod. ...Print use ABS.

25mm knob to be used with a M4 lock nut instead of the stock bed level screw nut of the CR-10 family. ...

... ...The original design was upside down. Large leveling knobs available on Thingiverse are for the stock knobs so I designed one that uses a metric M4 lock nut (nylon colar). Once leveled, always leveled. ... Hardware requried: 4x M4 lock nuts

Customized version of https://www.thingiverse.com/thing:215386 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=215386

Customized version of https://www.thingiverse.com/thing:3141591 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3141591

This is a combination of a laser and a bed leveling sensor mount for the CR-10, CR-10S and CR-8 :)

I buyed a digital depth gauge for levelling the bed of my CR-10S, but printable holders found on line do not fit my gauge This is 2 part print that must be glue together (see picture for final assembly) Print with your everyday settings, glue with CA...

Gif of it in action here: https://giphy.com/gifs/Js7ALWE0M9Q4IvR95P Attach to the side of the part cooling fan on your CR-10S Pro V2 and install a dial guage, allows for quick, easy and more accurate bed levling Works well with the Octorpint Plugin...

At Creality CR-10S S5 it´s not so much space between screw and frame. Here is my solution. No support is needed. Settings I used: PLA 210 celcius Fan 60% 60 mm /sec 0,2 mm level 30% infill, grid. ... 4 top level 4 bottom level 2 outline/perimeter...

it seems like there is a newer version of the Creality CR-10S with a solid version of the bed level knob (picture 4) I realy wanted to use this skeleton knob so i made a little adapter for it. ... you just have to press it into place and add a Nut on...

I did a remix for this mount because I wanted it to be more precise during the axis movement and the the needle to be automatically pushed down. I added some height to the model, and used just normal pen spring to push it down. There is a hole in...

Customized version of https://www.thingiverse.com/thing:3057714 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3057714

** I sold my CR-10S, so I will not be doing any more development / revisions to these file.** CR-10S Bed leveling wedge to be installed on the Y-carriage and under the insulation for the bed heater. Its adjustable from 13mm to 14mm. Designed for a...

A bed leveling wheel for the Creality CR-10s printer to make fine adjustments to bed height. Thank you to Oggie for supplying the original idea and the Fusion 360 file which helped enormously. When I printed Oggie's design I found that the...

Bed leveling knob for CR-10S s5 model printer. most (if not all other) knobs on thingiverse are designed for either older CR-10's or smaller versions. They will not work with Creality's latest large printer. This knob is specifically designed for...

This is my remix of LarnOm's great Ender 3 bed handle made for my new CR-10S (should fit Cr-10?). Anyway, it fits my 310mm x 310mm standard bed. I used Microsoft 3D builder to split the original file and then extended the middle part. Print...

I needed a replacement knob to fit the CR-10S S5. The bed is lower and the area for the knobs are narrower so many of the existing designs do not work. This version requires a 4mm brass insert for the hole. ...These can easily be inserted using a...

If you slice this you should print single layer squares, which allow you confirm you bed is level. At a given corner if the layer is too thin lower the bed in that corner, if the surface is bumpy raise the bed in that corner. If your corners a ok,...

Bed leveling knob for CR-10S s5 model printer. most (if not all other) knobs on thingiverse are designed for either older CR-10's or smaller versions. They will not work with Creality's latest large printer. This knob is specifically designed for...

Leveling knob for Creality CR-10S https://youtu.be/G5S57LttreM Creality3D printer beats all my expectations! I personally think this is the best printer you can buy within this price range and it’s currently being recommend by the community as the...

Z Leveling blocks designed for the Creality CR-10s Pro but works with most Creality or Ender printers/ . Designed to fit perfectly and makes checking the Z gantry is level before printing, easy. ... Print 2 and they will slot/stay together when not in...

Just received my CR-10S a week ago and was concerned the hot bed cable could catch on the rear left portion of the frame. Checked out the various supports for the CR-10/CR-10S hot bed cables and didn't find any that I liked. New to 3D printing and 3D...

Leveling knob for Creality CR-10S Assembly instruction: https://youtu.be/G5S57LttreM Hello Friend! Come to my website https://MyHobbyTools.com. There you can find links and reviews about quality hobby products. ... 3D PRINTING ✔ My Favorite 3D Printers...

Leveling knob for Creality CR-10S https://youtu.be/G5S57LttreM Hello Friend! Come to my website https://MyHobbyTools.com. There you can find links and reviews about quality hobby products. ... 3D PRINTING ✔ My Favorite 3D Printers –...