cr 10s filament sensor upgrade 3d models

This is a REMIX of https://www.thingiverse.com/thing:2935674 "New CR-10s Filament Sensor Housing Assembly" made by David Levy https://www.thingiverse.com/davidaelevy , but since the search in Thingiverse is so crappy, it's been impossible to upload...

The housing is specifically designed for the stock filament sensor that comes with the CR-10S. EDIT: I added a cable guide to the brace plate since my new aluminum extruder no longer has one. Also, I found putting on the nuts was quite frustrating,...

... Therefore, I created a new version of the stock filament sensor housing. When positioning the CR-10's filament spool holder on its back, rotating the extruder by 90 degrees was necessary, which also meant repositioning the filament sensor.

A revised version has been provided, eliminating the filament sensor requirement.

I'm looking to connect my drybox directly to my CR-10S Pro with a bowden tube. However, I opted for a more convenient approach - attaching a bowden pushfit connector in its place. This specific thread is an M10x0.9, so anything that fits here will...

The top cover is worn out, but i think im only one having this filament sensor with two screw holes

I had issues with my fully 3D printed hinged filament sensor, which consistently malfunctioned due to the filament bending slightly inside, causing the sensor to deactivate and interrupt the printing process abruptly. To overcome this challenge, I...

Revised: I moved the filament sensor to be more in line with the extruder and pushed it out to the edge, away from the Z chain. ... On the sensor's metal arm, you might need to bend it up slightly and cover it with tape, just like mentioned in...

Filament run out sensor designed specifically to work seamlessly with E3D / Clone Titan extruders. UPDATE 3/19/2019: Made adjustments to internal dimensions, ensuring a perfect fit for the sensor, and created a slot to secure the switch on the board...

... \r\n\r\nThis filament guide and runout sensor housing is primarily designed for filament spool holders mounted high, such as on top of the frame.\r\n\r\n--UPDATE--\r\nA new version has been uploaded to add stiffening ribs, improving part rigidity

... a little small and I couldn't tighten it enough to prevent it from slipping. ...Increased the size of the head so that it's easier to turn. Careful not to torque too hard - you can get a lot of torque and break apart the filament sensor's base piece.

Filament guide preceding filament sensor on my trusty CR-10S, a tried and true model from days of yore.

I've upgraded to a generic aluminum gear drive unit on my CR10S printer and discovered that the new filament path is a quarter of an inch higher than before. Anyone facing the same issue can take advantage of this solution and get back to printing...

Just updated a few things on the latest remix version here: https://www.thingiverse.com/thing:2951034 On my printer, the small locking piece is too small and the filament sensor isn't locked in place securely. The first two times I printed it, the...

This remix uses the same filament sensor as the stock one and can be easily swapped out with no hassle since they share the same connector. ...You can check it out here:...

I've designed a filament sensor holder that relocates the Creality original component to a more convenient spot when using a spool holder on top. It's perfect for those who want a better setup. I've gone through five iterations, and now I'm...

Just design a filament sensor holder to put the original that comes from Creality in a better place if you are using a spool holder in the top of the machine. I need 5 iterations to get it perfect, but now I'm very satisfied. ...You can put the...

... this, I integrated a 16x5x5mm bearing that enables it to pivot while ascending or descending. The original design would likely have been able to move, but incorporating a moving guide ensures the filament doesn't graze against the enclosure's walls.

This is idler is to align the filament from the filament spool with the filament sensor on an CR-10S Pro. ...

I've modified this filament guide https://www.thingiverse.com/thing:2756263 for the CR-10S by adding the original full box with a sensor holder that fits perfectly.\r\n\r\nUpdate: I've upgraded the model, and it's now available at...

Filament Idler for the CR 10S Pro printer.

I've been thrilled with my CR-10S for several months now, but lately my prints have been utterly subpar. After swapping out the nozzle and then the hot end, I discovered that the filament had worn away a groove in the extruder arm. (See photo) I...

... le câble PLA si oublié.. Filament guide before filament sensor cr-10s. Combine with https://www.thingiverse.com/thing:3047166 2019/02/26: - Strengthening of the upper part Top guide 2018/08/12: - Add Top guide without screws. ... Enjoy !

... if forgotten.. ******************* Filament guide before filament sensor cr-10s. Combine with https://www.thingiverse.com/thing:3047166 2019/02/26: - Strengthening the upper part of Top guide 2018/08/12: - Adding a Top guide without screws.

This is a Filament Guide for the V-Rail Designed Specifically for the CR-10S. It's Installed on the Top Center with the Wheel Located Under the Rail, Perfectly Suited for Direct Drive and Dry Storage Box Applications. ... Version 2 Offers a Sleeker and...

This upgrade is specifically designed for the CR-10S spool holder, but it can easily be adapted to similar spool holders as well. The key features of this design are: - No extra parts required - Reuses the stock spool holder - Reduces friction for a...

I reused the factory filament holder tube but wanted the filament holder detached from the control box. So I printed it in PLA. Update: 1-18-2018 I also included a version with wider uprights to strengthen the assembly and eliminate the need for the...

Anyone having issues with the sensor block of their CR-10S printer? ...My own sensor block kept floating away from the filament during prints, forcing me to create a makeshift solution to keep it in place.

CR-10S PRO Upgrade