cr10 x axis cable chain 3d models

This is a versatile chain designed specifically for the Y-axis, and it performs exceptionally well when printed using high-temperature materials such as ABS or any other thermally resistant filament.

cable gland chain for Anycubic prusa i3 printer

Remix to fit my Direct Drive setup with a cable chain. Here is the Direct Drive connector for this setup. ... https://www.thingiverse.com/thing:5404413 **Print as is with normal print support for the best results**

I just built an A6 and loved the cable chain concept, but wanted it to stay below the belt. I'm also removing the connector from the bed and soldering the wires directly, so I needed a new way to secure the bed end of the chain. ...Now you only need two...

This is a bracket to attach a 10 x 15 Drag chain on the X axis of the Gatton CNC. This is the one i used. ...https://www.amazon.com/Carrier-Enclosed-Plastic-Towline-Machine/dp/B01FYSQSEY/ref=sr_1_4?ie=UTF8&qid=1504367237&sr=8-4&keywords=drag+chain...

Drilling two 3.5mm holes and placing the cable chain 2-3mm away from the X-axis were crucial steps. To feed the cable through the chain, remove the expandable protection on the cable, separate each link, and then pass them over the connectors. ...I'm...

I replaced the mounts for the Y-axis chain because the Easyframe's dimensions don't match those of the A8 and AM8. To do this, I had to create new mounts. The frame has a hole in its proper place where you can attach the part that holds it together...

Open Cable Chain link from thing:611593 for the Y axis that fits on the Geeetech Prusa i3 Pro B's M10 threaded rod. You can adjust most distances and sizes in the SCAD file. Print Settings Printer Brand: RepRap Printer: Geeetech Prusa i3 Pro B...

Update 2019-01-23 : New design : https://www.thingiverse.com/thing:3377333 Update 2017-11-10: Use a cable chain bracket that is specifically designed for this purpose, as directly pinning cables to the chain with cable ties can make the assembly...

i make no promises, but the reinforced cable chain lid may provide enough structural stability on its own.\nplease note: the base mount features built-in supports that must be removed.\ncable chains can be obtained from this link:...

This is a bracket to attach a 10 by 15 Drag chain on the X axis of the Gatton CNC. I am using this one. ... https://www.amazon.com/Carrier-Enclosed-Plastic-Towline-Machine/dp/B01FYSQSEY/ref=sr_1_4?ie=UTF8&qid=1504367237&sr=8-4&keywords=drag+chain

This is a Reinforced and wider version of the Original Cable Chain brackets by Gnizten. They are designed for Igus E2i.15.20.xxx cable chains. Their inner width is around 29mm wide. I've also added some Holes to put in M3 heat inserts to connect...

Their Satsana remix has a very tight fit with cut-outs for the Satsana (which I use), so I've remixed their design with the original hot end connection to make an even better piece (and it really is a lot better than v1 and v2). I've also moved the...

This is a support arm that gives a stronger connection and less stress on cable chain (i used 17 pieces). ... Upper mount on exteruder group is ready for filament sensors like those:...

I decided to mod the original design to better suit a custom-printer cable chain link (This is the same link found here: https://www.thingiverse.com/thing:2920060) The version pictured for the bottom mount has holes in it but they aren't needed. ...

Remix to fit my Direct Drive setup with a cable chain. Here is the Direct Drive connector for this setup. ... <a href="https://www.thingiverse.com/thing:5404413">https://www.thingiverse.com/thing:5404413</a></p> <p><strong>Print as is with normal print...

The Easyframe's dimensions are different from the A8 and AM8 so I had to make new mounts for the Y-axis chain. On the frame there is a hole in the proper place, you can fix the part which is attached to the frame with a screw. I used double sided...

Made for a friend this uses a similar layout to the [CR Series & Ender3 X Axis Lead Screw Drive](https://www.thingiverse.com/thing:4820765) and uses [Lion Link Easy To Use Chain!](https://www.thingiverse.com/thing:3179124). The X board mount is for...

Due to the the solid top of the on the extrusions for the Neptune 2 and differing geometry for the extruder plate, there wasn't a good way to attach the cable chain for the x axis and extruder wires. The back mount simply replaces end cap of the...

This has also been routed under the cable chain. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.1 mm Infill: varies Notes: Print the frame and hotbed mounts with at least 25% infill and two or three shells. Print 14 chain...

... bed-thermistor connection at the plug had been replaced by a 2-pin Dupont connector due to intermittent contact issues causing Marlin to terminate prints prematurely. This new setup has also been routed under the cable chain for better organization.

This remix includes enough clearance under the stepper for safely disconnecting and reconnecting its cable, while extending the drag chain interface by 30mm to provide more space for filament to enter the extruder smoothly. ...With a single bolt holding...

I remix this cable chain mount from https://www.thingiverse.com/thing:4314829 so that it fits my Ender 3 V2 that is using the Satsana hotend fan shroud https://www.thingiverse.com/thing:4647053. I made one that shifts the mount over so you can...

Cable Chain Setup for Prusa Mini and Mini+ x-axis motor and the heatbed.UpdatedX-Axis chain can now mount on the front or side of the Aluminum extrusion!This has some other prints remixed in it.Prusa i3 MK3 Cable Chain Add-on (ALL...

I liked JohnnieWhiskey's v-slot mount but the angle of the chain connection was awkward for those cables that run by default under the printers bars. But with Mrrstrat they had the perfect angle but it required bolts and t nuts which I don't have...

Y axis cablechain for underneat the hotbed

Just my remix from Drag Chain - Cable Chain - Ender 3 by diogosantos88 June 26, 2019 for the TEVO Tarantula Pro. (not letting me tag the remix when uploading). The Ender has a 40mm X carriage and a 50m however the TTP has a 45mm. Also a different...

Due to the the solid top of the on the extrusions for the Neptune 2 and differing geometry for the extruder plate, there wasn't a good way to attach the cable chain for the x axis and extruder wires. The back mount simply replaces end cap of the...

The new files are named: - `X-Axis Cover - Chain Attachment + Lip.stl` - `X-Axis Cover - Chain Attachment + Lip - Part B.stl` This time no `.3mf` files since the `Part B` one is pretty much the same but made shorter and I forgot to save the `.3mf`...

Chain mount for ender 5 cable management. You can use these clips for the cable guides or just use zip ties. ... https://www.thingiverse.com/thing:4936515