cr10 x axis cable chain 3d models

These pieces will help mount a cable chain on a micro-swiss direct drive extruder, all the way to the Z/X axis rear bracket (ender 3 pro) without sacrificing printing volume/area.All the other mounts I found had the cable chain binding on the side or...

... cable chain ends for a 10x15 cable chain (Marked R18) from Ebay to accommodate the modified Z-motor position. The existing cables are secured with a piece of 1,85mm filament. Made preparations for the upcoming Z-Axis 10x15 cable chain installation.

Human: I couldn't find a suitable bed cable chain for the CR10 v2, so I designed one. The lug connects with the screws that hold the bed level sensor and slides over the plastic holder where the cable attaches at the bed end, providing a snug fit...

I've Simplified the printer settings to fit a compact X-Axis cable chain mount, which now allows the printer to sit perfectly on an IKEA Lack Printer table (available at thingiverse.com/thing:1843235). ... **Print Settings** * **Printer**: Anet A8 *...

Refactored the Chain Fence from the [Anet A8 X-axis Cable Chain](https://www.thingiverse.com/thing:398515) to print in two parts. This allows the Fence component to print upright which smooths out the vertical wall, reducing slip/stick friction on...

I really needed a X-axis cable chain, but I couldn't find a model that worked with my printer, so I came up with some new ways to install it correctly. The part attached to the X-motor is something I designed from scratch, while the mount on the...

To tackle my X axis cable management issues, I designed a variation on an existing chain. Previous chains either provided too little flexibility, caused excessive bending, or lacked support methods. My improved chain design doesn't require support or...

This is my take on a unified X and Z-axis cable chain for the Alunar Prusa i3 printer. The end piece of the extruder takes over from the X-axis end stop bracket. It supplies a filament guide while moving the end stop switch 10mm. This shifts the end...

This part was remixed specifically an early version of the Befenybay Direct Drive X-Axis Cable Chain on the Ender 3 3D Printer. Amazon Ean#: 0705300791787 The x-axis direct drive bracket has 2 wheels on top farther apart then the Micro Swiss Direct...

After installing it on the x-axis, I discovered that the cable chain would scrape against the left x-axis threaded rod whenever the carriage moved to the left. This friction caused the carriage to vibrate and distort my prints. My solution is to...

This is a X-axis cable chain for the Prusa Mini. After losing yet another MINDA probe wire to wear even with the "improved" anchor point, I had enough. It replaces the Extruder Front and Fan Spacer parts by Prusa to add the anchor points. You'll...

End of Chain for the X axis of the Anet A6 printer. ... This end is for if you have modified the fan support.

Update 4 (2018-06-17): added countersunk hole for chain fence Update 3 (2018-06-11): updated left motor mounts for different type of end switch Update 2 (2018-02-24): added chain fence Update 1 (2018-02-10): added info on possible z-axis problems...

My second update is the cable chain for the X axis. My problem is that, being in a wheelchair, my fingers have no strength and I didn't want to have to let go of everything to insert one by one into each link. ...That seems unnecessary to me and so I...

I used a DIY cable chain trick from Hackaday to design two printed parts that connect my x-axis cable, utilizing a full-size tape measure for maximum stiffness. The motor mount features a slot specifically designed to hold the metal hook end of the...

Changelog:\r\nUpdate 4 (2018-06-17): added countersunk hole for chain fence\r\nUpdate 3 (2018-06-11): updated left motor mounts for different type of end switch\r\nUpdate 2 (2018-02-24): added chain fence\r\nUpdate 1 (2018-02-10): added info on...

The following parts needs to be printed with support only touching the bed: XExtruderAdapter YBaseToChain These Parts needs to be printed with support everywhere: YChainToBed XCarriageAdapter I used 21 chain links on the X-Axis, plus the LinkWithGap...

I've been struggling with my x-axis cable chain for some time now. Every viable solution I've found so far pulls the hotend cables out of the main board every time Z moves above a certain point. So, I'm giving this one a shot where I've combined a...

I'm sharing a custom part for the Tevo Tarantula X-Axis, featuring a modified cable chain connector that's already assembled and includes a bearing reduction. I've also reinforced the plate with 4mm material and made adjustments to the offset. ...Check...

The printrbot Model 3 has a horizontal cable chain for the X/Y axis - though it's fixed with two screws at either end (two at the extruder, two at the frame), I don't trust that it will stay level over time. Since this is a large-format printer, a...

In addition to the left and right mounts, you'll need: 23 Cable chain elements from Anet A8 Y Cable Chain by sukhoi27 (download .stl file]). two screws to remount the x-axis endstop-switch for the longer left-side version: one screw ca. 3mm x 7mm...

X Axis Cable Chain Rail with Flat Heads Remix of https://www.thingiverse.com/thing:4702397 for https://www.thingiverse.com/thing:4316238 from Tobi0892 This is the adjusted rail from Verne64 with a couple adjustments. First removed material to...

The best X-Axis cable chain design I've seen on Thingiverse is by a guy that goes by the name of Juh, and was designed for the Anet A8. Juh's model was created for the classic Anet A8. By the time I'd purchased my Anet A8 last year, Anet had...

I purchased a 10x10 cable drag chain on Aliexpress (the link is https://es.aliexpress.com/item/Free-Shipping-Best-price-10-x-10mm-L1000mm-Cable-Drag-Chain-Wire-Carrier-with-end-connectors/32369095707.html). To complete the project, I just needed to...

This is a remix of Biffo318 Cable Chain for the cr10-v3 correcting some of the issues with the design overall everything is great but the control box mount sat 20mm to low from the hot end bracket which causes the chain to twist i raised the control...

I printed WAAAAY too many Cable Chains by johnniewhiskey to print more batches of the "Slim" cable chains. I decided to remix the extruder mount instead! So this mount is for the normal johnniewhiskey cable chains. Also, I JUST mounted my LEFT...

Mounting a heated bed to a CR10-S requires careful consideration of the underbed mounting options. A sturdy and secure underbed mount is essential to prevent damage to the printer and ensure smooth printing performance. ...The CR10-S's heated bed...

This Thing works with the ANET A8 | X-Axis Cable Chain, and I've got to give credit where credit is due. The thing that really makes this project shine is the EXTRUDER MOUNT, which you can find at https://www.thingiverse.com/thing:2099577. I also...

A Simple Remix from the Cable Chain Adapter for Prusa i3 by Hictop Allows Users to Easily Manage Cables on Their 3D Printer

Another Cable Chain but i designed some parts because i didn't find the perfect pieces for my 3D printer