cr6 se upgrades 3d models

A Minime cooling duct clone that mounts to the load sensor of the CR6-SE 3d printer. Uses the fan from the stock metal hot end shroud. The duct is designed to mount a Slice Mosquito hot end to the hot end carriage load cell. It is designed to...

This is a remix of 3dFreezeMe's awesome extended orbiter mount for the CR6-SE (https://www.thingiverse.com/thing:4818983). The only issue I had with the original is that it limited bed movement slightly in the X axis, where the extruder would hit the...

https://www.paypal.com/paypalme/jensterJ97 This base mount that was designed is used to modify the existing CR6-SE spool holder arm to allow it to mount on the top of the printer. The hardware used to mount the base mount to the top of the...

Hello Everyone, I Designd and Uploaded this Direct Drive Adapter for the Creality CR6-SE because i wanted to print with flexible Filament! The Adapter is Designd to work with the Following Stepper Motor: ...

Designed a camera case and mount for the CR6 SE. This pops right onto the x-axis mount. I put some double-sided tape to secure it on the x-axis. <b>Version 1</b> - My original design. It's kind of close to the nozzle. I can see my prints but it...

I split the original down to fit a single hex insert on the HSW, and just to hold the Allen Keys set provided with the CR6. ...&nbsp;Same holder works with Ender3 set.</p>

Here is my direct drive conversion on the creality CR6 SE using the BMG dual drive extruder. I've been using this for several weeks now and has been working great with no problems. (although there may be small updates to the design if I find...

When I screwed up my stock CR6-SE heatblock (don't over-tighten the nozzle, folks) I realized a replacement was a good 3 week wait. I didn't want to wait that long to continue printing, so decided to cobble together a mount for a V6 setup I had...

Remixed the Cprints CR 6 SE Filament Guide to fit the EZR Struder.

... layer to avoid internal supports. Here is the 24v blower fan I recommend: https://www.amazon.com/dp/B08R9J189T Also may I suggest you print this too and upgrade the front facing fan to a 40x10mm: https://www.thingiverse.com/thing:4774334

this file will make a cover for the extruder of the creality CR-6 SE printer, in order to avoid the cracking of this part of the printer. ... the cover must fit tightly over the extruder cover after printing.

REVISED 12/15/20Added a "bump" to click into place to avoid the part from pulling up.Another USB SD card holder. This one sits (hooks onto) on the Aluminium extrusion on the Creality CR-6 SE or any printer that uses the same extrusion rail.Holds 4...

... the part to "Click into place" Another USB SD card holder. ... This one sits (hooks onto) on the Aluminium extrusion on the Creality CR-6 SE or any printer that uses the same extrusion rail. ... Holds 4 USBs, 6 SD (full size), 6 micro SDs, and 3 Mini.

Filament Roller Spool Holder with ball-bearing for CR-6 SE / replaces holding rod for filament - mixed material PLA/TPU - one part is made of tpu for a better grip 2x ball-bearing "608" 8x22x7mm 1x p1,p2,p4 2x p3 pla 1x p5 tpu - TPU necessary for...

Attaches to two rail slots at the left side of Ender 6 SE. Gives plenty of clearance for the table to move. Printing: * Print the case standing upright. Use supports on the rail ends if you want. (I didn't and it printed just fine.) Installation: *...

Attaches to two rail slots at the left side of Ender 6 SE. Gives plenty of clearance for the table to move. Printing: * Print the case standing upright. Use supports on the rail ends if you want. (I didn't and it printed just fine.) ...

10-27-20 Updated all models I had a problem with some of them being lifted from the build table. I removed the...

Re-mix of a CR6-SE ribbon cable guide to personalize it up somewhat

A cover to protect the Creality CR6-SE Z sensor from bumps and dust.

CR6 SE Cable clip Guide with bowden Tube holder&nbsp;

This is a hotend mount for the Slice Engineering Mosquito. This mount also uses a 40mm cooling fan. ... requires -2 M2.5x20 -4 M3x12 -2 M3x8 -6 M3 nuts -40 MM cooling fan -slice engineering E3D groove mount adapter ...

Petg 40% 0.20

Did get heat creep so i designed a fanduct REMEMBER TO DO A PID TUNE AFTER

This is a remix from https://www.thingiverse.com/thing:398515

Piezas de sujeción cadeneta para carro con extrusión directa Bondtech LGX Lite

Remix of a Remix with camera mount. Enable print thin walls for the supports to print Properly. Use supports touching build plate only. It takes 4 M3x12 with nuts and one M3x16 with a nut. ...I used some removable Loctite to keep them from backing off.

This USB storage can clip into the side of the printer and can up to hold 6 USBs, 4 SD cards and 2 Micro SD cards

I didn't like the way the spool would drag on the stock holder so i designed something that would spin on a set of bearings. As the spool sits on a set of conical "cup" you should be able to use a variety of different spool sizes. ...This was tested...

This is a mock-up of the CR-X hotend assy.edit: 02-27-2021updated issues of holes and components not aligning properly from incorrect measurements on my part. ...I believe this now closely resembles the actual assembly.