creality cr 10 filament guide 3d models

This filament guide will guide the filament smoothly into your CR-10 Max, preventing the filament from scraping against the filament sensor as it enters the Bowden tubing. Setup: Print the guide, then insert a few inches of Bowden tubing into the...

Here's a custom-designed filament guide tailored specifically for the Creality CR-10 3D printer. To get started, you'll need to carefully tap it into place using an M6 tap set - you can refer to the attached photo for a clear visual reference. ... For...

Filament guide to stop filament from touching the z lead screw (needs a piece of PTFE tube fitted as shown in the pictures) This is designed so if needed, you can remove it while printing, but you would need to pull the PTFE guide tube slightly out...

This is a guide for filament on Creality Cr-10 when the filament spool is mounted on the printer's top bar. I discovered that placing the spool on the control box causes issues with angles, leading to snapped filaments and other problems. So, I...

This is a basic filament guide/cable guide designed specifically for the CR-10 and Ender-2 Extruder series, as well as their derivatives. It uses a 3mm or 4mm PTFE tube to keep the filament as straight as possible on its way to the extruder inlet,...

I recently purchased a Stronghero3d filament and discovered that the roll drags on top of the controller box when using the stock filament holder. This problem doesn't seem uncommon after looking around online, many brands use larger filament rolls.

I've extended the print head by 5 millimeters to accommodate the filament sensor on my Creality CR-10S printer.

Here is my improved filament sensor for Creality CR-10s made with guide wheels specifically for the Direct Drive machines with overhead mounts. ... Use your sensor and screws from original run out sensor, and print parts as listed, you will also need 2...

Remix of robathome (https://www.thingiverse.com/thing:3061551) updated version of Holspeed (https://www.thingiverse.com/thing:3052488) Ender 3 Filament Guide for the CR-10 V3 on the direct drive configuration. The CR-10 mounts the filament sensor on...

The original filament guide for CR-10 and Ender 2 doesn't mesh well with SeeMeCNC's EZRstruder due to the filament loading route colliding with the base of the guide. I've carefully trimmed some sections, resulting in a seamless fit now. ... It's...

Hi Maker, I've created a simple clip filament guide tailored specifically for the Tevo Tornado or CR 10, which can be easily attached to the top left corner of your printer. Simply install it and you're ready to go! ...Have fun printing with precision!

I was having trouble finding a good filament guide that fit my CR-10 and aligned correctly with the Bondtech BMG Extruder, so I decided to create one. This pressure fits into place. ... Hardware required: 1 x 608zz or 608rs bearing

Also, I've included a filament guide and an extruder cable guide for added convenience. If you find this design helpful, consider throwing me a tip as a gesture of appreciation. Thanks and happy printing! ... Print Settings: Printer: CR-10 Rafts:...

The problem with the original guide, though, is that when printing with bamboo or other rough, sticky filaments, its relatively small curvature can cause issues - the filament often gets stuck in the guide before even reaching the extruder. So I...

When trying to print some bamboo or other rugged or sticky filament, the fact that the guide imposes a not so large curvature to the filament did causes some issues with the filament being stuck in the guide even before the extruder. So I designed...

I adapted the extruder cover designed by graham01 to accommodate the CR-10 Mini's unique features. The lever arm on this mini printer differs significantly from its larger counterpart, so I made adjustments to ensure a smooth fit. To prevent...

I bought a CR-10 Smart and it didn't come with a guide between the extruder motor and the filament runout sensor, so I figured I ought to make one. Has a little window cutout to see that there's filament in there; it doesn't affect feeding.This...

Right now, I'm testing this bracket to see if it helps prevent clogging, and logically, this setup should guide the filament more smoothly into the hot end. ... To secure the bracket, I used an M3x20 Hex Socket Head Cap Screw that replaced the top screw...

... it use a single 608 bearing, shortened the length to fit in the box im making. ... 14/08/2021, Added a new guide piece to use an m8 bolt as I found the printed shaft failed too much. ... Also a new guide wheel design so the bearing fits a bit easier.

CR-10 Filament Sensor Housing 3 in 1 NOTE: The housing has been updated with improved features and design changes. When using the new input cone, it's essential to still install PTFE tubing through the input hole cut flush with the housing. The...

A Filament guide to suite the Creality Ender-3 and CR-10 printers. The tube size that fits into the end is the tube that comes standard with the Polymaker Humidifier unit, which is 4mm outside diameter. Just ask if this does not suit what you have,...

Simple filament guide for CR-10 printers. Tried to design it without a nut and bolt, but didn't work out as planned, so I added a printable one. Edit: Designed a redesigned bolt with an octagonal head and tighter tolerance on the nut. Edit: Added...

I have found that filament guides for top-mounted spools do not fit my CR-10 v2, very well. Some of them fit...passably...well, but most are designed for the Ender series; the runout detector and extruder and, most importantly, the carriage assembly...

... ...A PTFE tube, cut from a CR-10 spare part, was being used. There's a slight issue when removing filament as the blob portion won't retract back through the PTFE tube. A few upgrades for the CR 10, including some hop-ups, are available on eBay UK.

... - you can get these for under £3). Edit: 01/05/18 - added CR-10 file (haven't tested it yet, as my CR-10 is in the middle of a job).

(Note: just uploaded v2 which is smoother - photograph is of V2 - older version removed.) A Bowden filament guide, duster, and oiler designed specifically for CR-10 machines helps keep the filament away from the Z-axis screw-thread while cleaning it...

The author provides good information at this post: https://www.thingiverse.com/thing:4786557 I also printed the 608 bearing from Xtrudor found here: https://www.thingiverse.com/thing:3002837 My contribution was to bring together a fully printable...

A Filament Guide Specially Designed for Creality Ender-3 and CR-10 Printers. The standard tube size that fits perfectly into the end is identical to the one used in the Polymaker Humidifier unit, which measures 4mm in outside diameter. If you're...

My Customized Extruder Cable Support with Integrated Filament Guide. Edit October 15, 2017: Enhanced Strength by Adding Thickness. ... Introduced a Built-in PTFE Pipe Seat to Serve as the Filament Guide.

It's also expected to work perfectly with the Creality CR-10 Printer. Designed specifically for bearings of size 7/8" OD, 3/8" ID, and 9/32" W, this guide is ready to go. If you don't have a bearing in this exact size, simply purchase a pack of 10...