creality cr 10 v2 3d models

Filament sensor mount for the Creality CR-10 V2.

... to hold your cable in place. ...(No more messy cables!) It clips tightly onto the base frame of a Creality CR-10 V2 while allowing minimal cable motion along the in one direction. ... Compatible with other 3D printers that have the same 20x40mm v-slot.

Adapter for Creality CR-10 v2 printer. 
With it, the printer becomes Direct Drive, eliminating the Bowden feeder and preparing it for TPU-type filaments. Designed for printing without supports. They are two versions. One version with filament sensor...

This is a ventilated cover for the power supply to the Creality CR-10 V2

This is a model of Creality's heatbreak for the CR-10 V2/V3. I suppose you could print this, but my intention of sharing is for it to be used as an aid for designing modifications for the CR-10 V2/V3. ...STL and Step file included.</p>

You can't find your Tools? ...Workspace looks messy?! NO PROBLEMO!!! It's a Toolholder for Creality CR-10 Printer. ...Probably compatible with other 3D-Printer, its very standard designed.

This is not really a remix of the [cable holder](https://www.thingiverse.com/thing:4529886), (which looks exactly like the stock clip delivered by Creality with the CR-10 V2), but a new design. I wanted to cover the V-slots of the frame (at least the...

I´ve constructed an upgrade for the bad filament holder of the Creality CR 10 2. The distance between the ball bearings can be adjusted with a crank. The main holder is fastened with a large nut. Use two ball bearings with the following dimensions:...

Dangling calbes of the Creality CR-10 printers have always been a problem, especially the bed heating cable was always likely to get stuck at the corner of the bottom frame. Therefore I had alredy created a corner slide (simply replacing the 20x20...

This is an adapter plate to mount the stock Creality CR-10 V2 or V3 fan and hotend to the Wham Bam Systems MUTANT.

Mount for BL-Touch on a Creality CR 10 V2 Printer. The strengthening is in the same angle like the strengthening for the whole Printer. Unnecessary middle hole for the Bl-Touch removed. ... Enjoy printing :-)

Mount for BL-Touch on a Creality CR 10 V2 Printer. The strengthening is in the same angle like the strengthening for the whole Printer. Unnecessary middle hole for the Bl-Touch removed. ... Enjoy printing :-)

Based on the design from Pestkowiec, this is a remix that works with the Creality CR-10 V2 / V3 3D printers. I used M5 x 10mm bolts with M5 t-nuts to secure the feet to the 2040 extrusion frames. "t3dhlefttallsbfv2" is the stretched out version...

I really liked the Filler creation by HugoHuge: https://www.thingiverse.com/thing:3020026 But I needed an angled adapter for my Creality CR-10 V2 and found DasMani01's, which is great! : https://www.thingiverse.com/thing:4333402 However, I...

Рекомендую использовать с креплением под директ: https://www.thingiverse.com/thing:4491805 Smooth fang mount for the Creality CR-10 V2 + 40mm fan duct. ...</b> <b>Compatible with:</b> https://www.thingiverse.com/thing:4389912 ...

I made this to mount my Nest Home Outdoors camera to my Creality CR-10 V2 printer so I could monitor prints and create time lapse of the prints. If you would like to use the bracket then you will need two 2020 extrusion corner brackets, four m5 x .8...

Made this because I ran the nozzle into the bed a few times and for the life of me I could not find documentation or any blurb on the web of what direction to turn the knob on my Creality CR-10 V2 to make the Z axis (or Zed depending on what side of...

... for the filament feeder. Be sure to align the pulley with the entrance to the filament sensor. I used a 608 ZZ skateboard bearing in the pulley.Version in photo was printed on Creality CR-10 v2 with generic PLA, 0.4mm nozzle, 0.2mm layer height.

I made this because I ran the nozzle into the bed a few times and for the life of me I could not find documentation or any blurb on the web of what direction to turn the knob on my Creality CR-10 V2 to make the Z axis (or Zed depending on what side...

Complete set of slot covers for the base of the Creality CR-10 V2. Does not include the gantry rails. Didn't do it for looks, but to keep filament out of the rails. The flange extends to the center of the rail so stuff doesn't get caught between the...

Complete set of slot covers for the base of the Creality CR-10 V2. Does not include the gantry rails. Didn't do it for looks, but to keep filament out of the rails. The flange extends to the center of the rail so stuff doesn't get caught between the...

This is a remix from https://www.thingiverse.com/thing:398515 I think it's about a 80% sound reduction. Placing the printer on my tile floor toke away the stepper sound. The ground plate didn't fit my version of the power supply so I only used...

Had some old Flashforge filament spools laying around, however the spoolholder to my creality CR-10 is too wide to accept them. So I made a new spool holder using TinkerCAD that fits the nut from creality. There are other designs for this purpose,...

When loading filament into the CR-10 v2 from the top the filament can put stress on the filament sensor. The filament rubbing against the sensor entry has the potential to leave debris that can block the sensor and can sometimes squeak. This pulley...

Front and Back Corner Brackets: remix from 2020 Corner Bracket by TheStapler https://www.thingiverse.com/thing:2655498 Spool Holder is from Super Simple Spool Holder by bdx2000 https://www.thingiverse.com/thing:2165694 I used Y axis cable chain:...

Wanted Dual Extruders on my CR-10 so I remixed this. I tried it first without modifying it but I think the original was for the older BMG X2 (With smaller C-C spacing). Second itteration I tried to assemble the extruder on the X-Cariage, but it...

Direct Drive mount for the stock CR10 V2 extruder Very quick and easy to print. The extruder faces forward for ease of use and visibility of the drive gear. There are two models - one with and one without the filament sensor. Filament sensor...

I designed these to add more tension to the bed springs. The back left is different because of the bed heater wiring mount, mine was all bent out of shape where the spring sat and half way pushed in, so I came up with this idea to do away with using...

Hi, this is a Spool Holder i designed myself cause i didnt like the other ones too much. Easy to print and to install. You can use the original clamp to fix the part. ... You need: M8 rod around 100mm long M8 nuts (3x) M8 washers 4 4x 608RS...

KATAMCO makes this really awesome filament box. ... The only problem I had was that the weight of the filament tube was putting stress on the filament and a significant bend at higher z levels so I designed this adapter in OpenSCAD to support the tube.