creality cr 10 y axis pulley 3d models

This is a Z-axis full setup for my project to transform Tarantula into CR-10. It involves using aluminum V-slot profiles. The x-axis uses profile 2020. This is an alternative design that shifts the motors down. If you prefer to mount engines on top,...

The CR-10S is a seriously good printer, but what's not good on this printer is the sloppy Filament Run Out sensor mount and the cable management is a true mess. Specially the Z-Axe cables which are all just hanging loose in the air and causing...

Pre-lube everything if you want to do it now or save the mess & wait until its mounted.BOM1 x Ender-31 x 300mm MGN12H linear rail2 x M4x20mm screws2 x M4 t-nuts2 x M4 washers4 x M3x25mm screws16 x M3x8mm screws12 x M3 t-nuts4 x M3 locknuts12 x M3...

The STL file contains two pieces for assembly - smaller one around the hex nut under Y-axis pulley and larger one around Y-axis edge. ...Drop M3 nuts into respective slots in the smaller piece, insert M3x16 bolts, and tighten them for enhanced Y-axis...

If you have decals on your Z axis to help with setup, you should be able to push this right into the 3mm screws holding the X extrusion onto the Z axis extrusion to point at the decal lines and make leveling your X gantry a lot easier. I haven't had...

A Simple but dimensionally accurate model of the Creality CR-10 V2 and V3 X Carriage plate with V-wheels.

Feel free to resize the width as needed or simply let me know and I'll take care of it for you.

it need 2 10mm X 50mm bar and 16 M3 bolt and nut

I designed a lower bearing block to reduce vibrations while printing tall objects, ensuring smoother prints and increased accuracy.

For CR-10s sold in Korea during 2018, the T-bracket and X-axial motor bracket were made of plastic, rendering them extremely fragile. ...So I created a solution.\r\n\r\nAlthough this is my first project involving 3D modeling, I hope you find it...

The X axis reaches its maximum height without coming into contact with the reinforcing bars. If you have any doubts about your installation, don't hesitate to ask for assistance. Materials: 2 rods 8 M 8 nuts 8mm 8 washers 8mm Note: Applying...

used the original as a blueprint mostly for size and hole position and added a spot to mount bl/cr touch, the precise one should fit titan hotend/extruder perfectly and have touch at optimal height to probe and be out of the way when printing, i have...

This is a super simple adaptor to allow you to attach a 8mm Pulley Bore to a 5mm Motor Shaft. I did this so that I could attach a dampener to the y-axis (bed) of my Ender 2 Pro and adjust the pulley to correctly align the belt. This was easier to...

... of the camera. There are a few options - I found I preferred the "5mm_wide_extension_no_nut" with the "camera_swivel_shorter_no_nut" - although I'm actually using a different x-axis cover I've put up here https://www.thingiverse.com/thing:4657122.

This is to complete my set of knurled knobs for the Creality Ender 3 / CR-10 / Ender 3 Pro (extruder knob, Z-axis knob, and finally control knob - I like them all in the same design). Simple, stylish, ergonomic. Printing. Printing should be really...

... smaller piece should fit around the hex nut under the Y axis pulley. The second piece should fit around the edge of the Y axis. Drop two M3 nut into the slots in the smaller piece that fits around the Y axis pulley. Insert two M3x16 bolts. Tigthen.

These are my upgrades for the Creality CR-10 S5 500mm printer. The frame braces and spool holder utilize M8 threaded rods and M8 nuts. The spool holder relies on two 608 ball bearings The rods must be at least 72 cm long for the two braces and...

This is a remix of the combo XZ bracket from stevenfayers' [Creality CR-10 Z axis cable drag chain by stevenfayers - Thingiverse](https://www.thingiverse.com/thing:2757810) and fellini's [CR10 Camera Bracket by fellini -...

Knob for Creality Ender 3 extruder features a finger tip depression to enable fast scrolling and matches the Ender 3, Ender 3 Pro, CR-10, CR-10S, and CR-10S Pro designs. ...To install it, you'll need an M3 screw.

#ZKNOB This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw. It lets you manually control the hot end up and down when steppers are disabled, which I have found to be very handy at times. For...

**#ZKNOB** This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; it lets you manually control the hot end up and down (when steppers are disabled), which I have found to be VERY handy at times. I...

From the creators of Ender 3 The Hole Protective Cover. ...Creality Ender 3/Ender 2/CR-10 Extruder Motor Shaft Protective Cover. Protect your motor from filament crap, keep it clean and happy! ...Happy extruder - happy prints!

Big Extruder Knob for the Creality Ender 5 / Ender 3 Pro / CR-10 Maybe there is someone out there need a bigger extruder knob like i did, 150 micron, 25 infill, and pla will be enough

Users seeking a custom engraving for frames like the Ender 3, CR-10, or similar models with four-corner profiles can utilize the Creality logo insert. ...This enables users to personalize their 3D printer's frame with a unique identifier.

Here is a rewritten version of the text: Custom LCD and Control Knob for Creality Ender 3, Ender 3 Pro, and CR-10 Models. ... Remixed from Original Designs by Guppyk (Thingiverse: #4204606) and Inuit (Thingiverse: #3611103).

This mount attaches a bed leveling Dial Indicator to the 20x20 rail of my Creality CR-10 printer. I used an indicator from Amazon. Let me know what you think, and I have more ideas that can easily be adapted to other printers with extruded aluminum...

Since the CR-10 is a huge bed slinger, adding weight to the x-axis sled basically has no performance impact. So far, I've noticed no stringing and I was able to reduce the retraction distance from 5mm to 0.6mm. ...I did buy a new cable for the stepper...

This replaces the X-axis motor cover/limit switch box one that contains mounts for the Creality CR-10 filament runout switch v2 and a PTFE tube fitting -- perfect for direct-drive setups. (The X-axis limit switch installs into this as well.) The...

This tray fits in the Creality CR-6 drawer to give you SD card and tool storage.

This tray fits in the Creality CR-6 drawer to give you SD card and tool storage.