creality ender 3v2 3d models

... Update 03/19/21: - Mesh Fix: added recesses for the screw heads. - Note: My print settings say Ender 3 Pro; but, that's only because my Creality models aren't listed. ...I printed on my CR6-SE and installed it on an Ender3 v2.

Ender 3V2 Unitak Direct Drive wire guide No amount of zip ties and trying have I ever managed to get all the wires in a place that didnt either catch on the frame when calibrating before a print or when bed levelling, or if i did it looked an eye...

Version 2 available: Ender 3V2 Damper Feet (Soft Springs) von AaronLK As far as I can remember my engingeering-courses the machine should sit on springs as soft as possible to reduce vebrations from/to the environment. Standing on a IKEA Lack table...

It secures to the frame using the two screws in the front of the ender 3v2 extrusion on the left side so needs no extra hardware. The fitting for the screen to clip on to it is deliberately tight. You will have to sand a little off for easy fitting...

Remixed from https://www.thingiverse.com/thing:3147743 , this is a webcam mount for a Creality Ender 3 v2. Features: * Provides a front-view perspective of the Ender 3 v2 * Mounts to the belt tensioning device on the front of the Ender 3 v2 * Made...

Niggled me constantly after that, consequently I designed and printed this small cover for the Z plug.  The ender 3v2 z stop connector comes out of the top of the circuit board enclosure and looked like way too much messing about to delete for little...

null Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

... any of your parts of original version (like I did), you could use this version instead. These two versions are compatible. # Printing Settings: Printer: Creality Ender 3 V2 Filament Material: PLA Infill: Gyroid, 15% Support: Yes Adhesion: Brim

null Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing

Ender 3V2 Noctua 4020 fan mount This is a little design based on the stock Ender 3 V2 hotend cover. I dont think it will work for other Ender 3 models due to the carrier plate, but didn't tested. I needed to make my Ender more silent so switched to...

This is a remix of my previous design for the Voxelab Aquila, designed instead for the Ender 3v2, which I also have. I wanted a very clean and compact design that held the ultra cheap runout sensor I purchased and guided the filament with a...

As those of us with Ender 3v2 machines will find out, the stock cooling duct will slowly deform and melt causing us to replace it. Many of us have looked for replacements, upgrades and anything else useful to fix this. I have ran other common hot...

This is a little design based on the stock Ender 3 V2 hotend cover. I dont think it will work for other Ender 3 models due to the carrier plate, but didn't tested.I needed to make my Ender more silent so switched to various bigger Noctua fans for the...

As those of us with Ender 3v2 machines will find out, the stock cooling duct will slowly deform and melt causing us to replace it.  Many of us have looked for replacements, upgrades and anything else useful to fix this.  I have ran other...

A quick camera mount I made for my Ender 3v2. I am biased, but I think this is a really great solution for mounting pi cameras on this printer, and I was a little surprised nobody seems to have made one before. It is very secure, offers a good...

The ender 3 V2 hot end assembly attaches with one screw in the back, instead of two in the front on the ender 3 and ender 3 pro. ...I made a small change in this part to go around the screw on the ender 3 V2.

Scaled down the knife to fit a ender 3 v2's print bed.

Original direct drive from Creality came with plastic feeder , so I designed motor mount too use with my dual aluminum feeder.

What i used: Slicer: Cura Infill: 20% Support: No Adhesion: No Material: Basic Pla Printer: Ender 3 V2 Neo

Scaled down the knife to fit a ender 3 v2's print bed. Category: Other

This is a remake of thing:4594025. ... It includes slots to see the time on the Ender 3 v2 Screen. ...Thanks to the Original Designer for the design

Remixed version of the RODAM Ender 3 spool holder, which was made by Rodamyot. ... This version can handle some larger spools.

Y-tensioner (for ender 3, V2,PRO) modified for installation of a direct drive (see my YT chain with direct drive links). ... Modified by SIX SAUER ;-)

I combined 2 models to create this extruder knob topper for the ender 3 v2 https://www.thingiverse.com/thing:4736138 Ender-3 v2 Extruder Knob Overlay by edk_sc January 24, 2021 https://www.thingiverse.com/thing:2033990 stackable fallout vault door...

Since the filament holder faces the bed, I edited the Ender 3 holder from https://www.thingiverse.com/thing:3209211, by https://www.thingiverse.com/mjoaris. This will hold all 1kg filaments no problem. This is almost the same size as the stock...

I shortened the rail to fit on Ender 3 V2 (150mm) and support the wire guide. ... UPDATE: added a cover to just let the LEDs shine on the bed and hide them from front side

i maid a base for the stock ender 3 spool holder so it's sepret from the printer it has no problen holding more then 1 kilo of filament to assemble you need two m3 screws

It is an end switch cover for Ender 3 V2 but it would fit on others with hight of cover 42mm. ... I took dmaccalums awesome design (thank you) and scaled it down and added a bracket.

They look good and add a nice bit of storage.  If you have an Ender 3 or Ender 3pro, you might need to move your screen off the top of the extrusion where the drawer body would go. ...You can use this bracket to move the screen over to the side:...

Will fit Ender 3 V2, Pro and clones. ... https://www.waveshare.com/product/5inch-dsi-lcd.htm https://klipperscreen.readthedocs.io/en/latest/ Other hardware: M3x10 Socket head cap screws 3pcs M4x10 Socket head cap screws 4pcs M4...