criss cross pattern 3d models

(I use 150% for external perimeters, and 112% for the other lines)Infill pattern: Gyroid.Printing temperature: As high as the material allows without material degradation.Printing speed: Low to medium. (I use 30mm/s for external perimeters, 45mm/s...

The lights have an expected lifespan of 8,000+ hours and emit a flood beam pattern. A surface with 43% reflectance promotes UV light distribution and ensures maximum exposure. Inside the box, the UV system offers three 20" lamps on each side (left...

1.0mm top/bottom thickness, concentric pattern. 96% infill, cubic. Print thin walls off. 0.4mm line width. Duct Ring: Same as main frame. Ducts: Spiralized (smooth contours enabled), 0.2mm layer height, 0.3mm initial layer, 0.4mm line width. 0.4mm...

In modern electronics, a Lamp is a component producing light such as Arc lamp users, or the more popular Ultraviolet lamp emitting black lights that reveal hidden patterns and invisible objects like Wood's lamp does in various health care settings,...

Thanks go to Keichide for the hint.To have comparable swatches as the ones posted here, please print the swatch atLayer height .2mm2 Perimeter5 Solid layers20% infill (fill pattern grid, fill angle 45 degree)Don't use supports. ...The structures are...

Use strong supports, I used grid pattern @ 35%. The female thread on my clamp looked like it failed at first, but when I screwed the insert in the first time, a bunch of crap came out and revealed the proper thread. Post-Printing Required Hardware ...

That means thick walls, a hot extruder, and a good infill pattern. I'd strongly suggest ABS (or other tough material) over PLA. As with any tall skinny part, adhesion to the base is important, so I'd suggest using a raft. The part is designed to...

The term may also refer to a state of sexual arousal[1] or anticipation of such – an insistent sexual impulse, desire, or pattern of thoughts. As French novelist Honoré de Balzac stated, eroticism is dependent not just upon an individual's sexual...

Follow the same pattern if you print on a larger printer. Make sure to still print the "sliding supports" You should not need to print with supports. Mine turned out fine without it. I printed mine using PLA but if you plan on leaving yours in...

Since I like the stripe pattern on the surface that is created when printing, I printed these the right way up, which then requires supports. If you print them upside down you don't need supports and get a smoother surface. Figures: The figures are...

- Layer Height: 0.16mm - Wall Thickness: 0.8mm - Wall Line Count: 2 - Top/Bottom Thickness: 0.64mm - Layers: 4 - Infill Density: 20% - Infill Pattern: Triangles - Printing Temp: 200°C - Build Plate Temp: 60°C - Printing Speed: 60mm/s - Initial Layer...

This is a parametric set of cards (quantity of card can be configured) that allow the owner to do a simple but amazing magic trick, here are the details:Example RoutineThe magician ask the spectator to think in a number between 1 and N (N is...

If you however have something like a usb-cable or just a thin not so thick or short one, you might wanna use the saml rescaled version instead. I have printed many big and a few small ones with said Gcodes, and the settings are dialed down...

You might find an interesting pattern for these pieces. Insert the folded main part into the frame, starting with the bottom of the box. The inlet has two tiny gaps, which should point towards the top of the box to keep the folded edges in place. Be...

I started with a basic honeycomb pattern in Fusion 360. I took inspiration from various tube racks in the lab and different designs on Thingiverse. I tried different kinds of feet for the bottom part, but these bigger more rigid ones came out as most...

It is an optional print to use instead of the baseplate, but it integrates the baseplate into the bezel and relocates the reset button a bit for better access.- Rotated the embossed pattern around outer gear to leave walls thicker for FDM (V22)-...

For tightening the screws it is recommended that screws are tightened in diagonals in an X pattern to ensure even thermal paste spread and pressure across the CPU Die. Step 6: Slot the CPU Daughterboard back into the system, make sure that even...

Diffuse map helps us achieve photorealism when viewing real objects and how their colors react under light conditions with various textures involved like albedo mapping above however does so without affecting reflection patterns instead providing a...

I used a brown spray paint for my grips (A) and then added some grain patterns using blacks and dark brown acrylic paints from Walmart. I then heavily watered down black and brown acrylic to add some aging and rust to my pistols. I sealed the paint...

Here are a few of my key takeaways: - Print with heavy infill, otherwise, your thicker parts show the infill pattern. I would use at least 80% infill. - Print with the lithophane vertical, with it standing perpendicular to the X axis movement for...

*The board will be cooled by separate 5015 * Drill holes in close enough pattern to as visualized above. * Drill 3mm holes for the usb panel mount extension but putting the extension in place and using the a smaller bit to mark the holes through...

Top and bottom fill pattern ‘Concentric’ 3 Perimeters Seam Position Aligned Recommend printing 'Output options:' set to enable ‘Complete individual objects:’ with a height clearance of 14mm my clearance ‘Radius:’ is set to the default 45mm CAUTION:...

It was created by taking the NIH approved visor and flattened with patterning software and modeled tabs so that it can be added to the Prusa 4-hole layout. The removable visor can be 3D printed or laser cut for maximum efficiency.</p> <p>I have tried...

... together. The bolt pattern is symmetrical, so simply aligning any bolt with the split where a pipe was cut in half, or toward the "top" or one "side" of the model is sufficient. ...Maybe at some point, I'll key the models' pieces to deal with that.

UPDATE: 3/13/2023 - Alternatively to suggestion from 3/3/2023, print with 4 layer walls, 50% infill, and gyroid infill pattern to increase longitudinal (direction of longest dimension) shear strength. UPDATE: 3/8/2023 - I found that the option for...

The middle cover took over four hours, but I used Archimedean Chords for Top/Bottom fill & 3D Honeycomb for fill pattern which I thought made it look nicer. I also included the openscad files of these, which give you the ability to change it a...

I want to see the wear patterns to see if modifications are necessary. All in: I have about few hours of cad work a few hours of print time an hour in the oven 15 minutes of clean up and about $4.25 worth of filament. to replace... well the least...

The outer (longer) pins of the steps should now be sandwiched between the track guide and the handrail guide.Start placing chain links on the pins, following an alternating pattern. First join pairs of steps together with the chain links (making 16...

The fan openings continue the hex pattern of my extruder fan grille, thing:1504489. Strength comes from 2mm high, 2mm wide ribs all around the perimeter/tabs and to the power opening. Since the tab and power plate screws are m3 threaded, the power...

The things I change most often are top/bottom layers, infill ratio and pattern, number of perimeters, brim, and ‘infill only where needed’ or not. Obviously sometimes supports need to be enabled. For some prints you may need to make pretty drastic...