dart board mount 3d models

Mount / case for MDFLY 4 channel RJ45 ethernet connector breakout board https://www.mdfly.com/products/1x4-4ch-rj45-ethernet-connector-breakout-board-w-led-spring-screw-terminals.html 50 x 82 mm PCB Two versions with mounting tabs in different...

This custom camera mount is engineered specifically for the Flite Test Versacopter, seamlessly integrating a Mobius Action Cam atop and a standard full-size board cam below. Proper fitment of your board cam may necessitate inclusion of 5mm spacers...

A din rail mount for an eight position relay board The board I used can be found at: https://a.co/d/0wXVFYN They can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab The project...

A mounting bracket to Duet 2 WIFI board and the gpio extension board. You will need to print two tabs for the bracket. ... They can be found at: https://www.thingiverse.com/thing:3401942 or...

... comfortable putting my electronic board in a wooden box without a sturdy mount. ...That's why I decided to design a simple holder myself. The first iteration was just a basic holder, while the second version featured holes for secure board mounting.

this is a very powerful blow dart goes very far this took me a lot of time to design so please like if you like my design it also has a built in safety ring so you don't suck in the dart keep away from eye and use safety things i am not responsible...

Get the entire file here: https://cults3d.com/en/3d-model/gadget/meepo-board-electric-skateboard-double-bar-flashlight-mount OR: https://www.cgtrader.com/3d-print-models/gadgets/other/meepo-board-electric-skateboard-double-bar-flashlight-mount This...

Get the entire file here: https://cults3d.com/en/3d-model/gadget/meepo-board-electric-skateboard-double-bar-flashlight-mount OR: https://www.cgtrader.com/3d-print-models/gadgets/other/meepo-board-electric-skateboard-double-bar-flashlight-mount This...

A mounting bracket to Duet 2 WIFI board and the gpio extension board. You will need to print two tabs for the bracket. They can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab...

This dart holder accommodates darts with bodies under 10.1 mm in diameter, its capacity bounded by the topmost opening.

... ties.Use this board with M2.5 12mm spacers and a 1.6mm thick OpenMV Cam board. E.g. our dual 1x8 pin designs or full board length shields.You will need a 1/4-20 hex nut which you can press fit into the back of the case for the 1/4-20 tripod mount.

I designed a mount that makes it easy to attach the "upgraded circuit board" version using simple standoffs. It then snaps onto a 3/4 inch copper water pipe, allowing you to place it almost anywhere. The hardware includes (2) M3x16mm bolts with...

I ordered a Raspberry Pi Compute Module along with an I/O board for a project I'm working on, but I didn't realize until it arrived that there was no mount or case included. No problem! To address this issue, I designed a custom mount that allows me...

This frame is designed specifically for mounting on ply-board, and it works with any MKS board since it's not attached directly. The frame was actually created to work perfectly with the MKS Base 1.4 board to provide maximum cooling for the servo...

I mounted a CC1333 Board Camera on my ZMR-250 using this method.\nThe raised points on the back of the mount provide clearance for the crystal component, ensuring it doesn't interfere with the mount.\nThe lugs at the top and bottom fit snugly into...

Mount the Keyestudio W5500 board in a custom module designed specifically for installation in a 19" DAP 2U rack frame. To unlock the full potential of this module, remove the power jack from the board itself. The front plate boasts three...

The mount positions a Raspberry Pi camera board at a 45-degree angle relative to its attachment point, while providing adequate clearance for the data cable to coil beneath the board, thereby conserving space. ...The depicted setup illustrates its use...

A module for the Keyestudio W5500 board to be mounted in the 19" DAP 2U rack frame. To use the front plate you have to remove the power jack of the board. The front plate has three 3mm holes for LEDs. Use M3 screws to mount the board (would recommend...

... as standard 30x30 and compact 20x20 FC boards. ...To enhance versatility, I incorporated mounts for three stackable components, allowing users to easily install a Power Distribution Board (PDB) or a VTX module that can be stacked with other components.

A mount for an Arduino Uno with proto board for Din rail. You will need to print two tabs for this design. ... They can be found at: https://www.thingiverse.com/thing:3401942

A slight remix of the mount made by gatenosix, the main change was to extend the clamp to fit the vertical wooden board on my Ikea Brimnes daybed which I measured to be about ~22.9mm thick.

I made this soldering iron mount for Parkside Wall Tool Storage Board, for a 15 mm wide soldering iron (as in picture). ...The inner diameter of the ring is 18 mm.

This is a mounting platform designed specifically to hold a 40x40mm fan, primarily aimed at cooling the X and Y stepper-motors on a Makerbase Gen L board, which is commonly utilized in the JGAurora A5.

Improved front cover for Prusa i3 Mk 3 and 3s printers that includes a mounting point for E3D PT100 board. ... https://www.prusa3d.com/prusa-i3-printable-parts/ https://e3d-online.com/products/pt100-temperature-sensor

A mount for SparkFun's quad relay board. ... https://www.sparkfun.com/products/16566 You will need to print two tabs for this design, which can be found here: https://www.thingiverse.com/thing:3401942

I'm designing a simple mount for a 28BYJ-48 stepper motor and its accompanying driver board to keep everything neatly organized. I recently received a batch of 28BYJ-48s, and I found that the motor mount fits perfectly. However, my control case is a...

This is a quick part for attaching the SeeMeCNC HE280 accelerometer board to the 713Maker hot end mount. I haven't gotten the board wired yet, but this looks like it will do the job just fine. The part attaches to the hot end mount with regular...

To enhance airflow around my RAMPS board, I mounted a 40mm fan vertically beside my rostock-mini's acrylic base. This "L" bracket facilitates vertical mounting on flat surfaces with 4 fan holes; however, the STL file doesn't include bracket mounting...

Dart Players Boost Performance with Targeted Training Rigs Trained dart enthusiasts securely fasten precision-crafted training rigs onto a sturdy board using slender, high-tensile pins.

* The fan frame mounts to the base at two hinge points using M4 screws, allowing you to open the fan just over 90 degrees to gain access to the board. There is space in each hinge for a couple of washers. * The fan frame has a hex grill in it to...