dart model

You just have to have the right case respectively.If you use the original MK3S+ frame check out the version for the original Prusa frame. FeaturesWorks with Raspberry Pi 3 and 4Works with any type of Armor-style case that uses M2.5 screws. Just...

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

I also adjusted the tolerances of the nozzle wrench brackets so that they fit a bit tighter.I also felt the cover did not latch securely enough, so I also deepened the magnet pockets on the case, so you can stack two 6x3mm magnets in each pocket.I...

I have reported this bug to the developers with this issue that they hopefully fix soon: https://github.com/tzapu/WiFiManager/issues/1609 —> Problem solved!04.07.2023: Release of software version V1.8.0:Replaced the old WiFi manager library with my...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 0 pattern_element_overlap = 0 stencil_shape = 4 custom_back_camera_y_size = 20...

The resulting "cylinder" is much stronger - I even tried to bend/break it without success. The hole piece was created with the following drafts and results : Bottom row, through holes (left to right) : 1/2° draft = very tight fit, very difficult to...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

... the strip about centered under the nozzle I knew it was pretty good. I have thought about adjusting the model to match that, but haven't yet out of laziness but also concern that some blowers may behave a bit different. Category: 3D Printer Parts

I always wanted to design and print a swamp boat. Now it was time to realize it. The boat consists of two parts, which are screwed together. For sealing the whole thing is glued around the internal cable duct. I took the motor and ESC out of my MHQ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 0 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

The feet need to be modified to include more bracing and pulleys/motor are still being fine-tuned(NEMA17 works great but it's the most complicated).\nInstructions are still being worked on and model files may be reorganized or changed.\nThat being...

Being in the United States, getting replacement parts for British model locomotives can be challenging, un-environmental, or impossible. but I found that the Bachmann Percy chassis shares a similar wheelbase to the 0-4-0's, and the Bachmann Duck...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

We'll be using a simple character model for this exercise, so go ahead and import it into your scene. You can find the model in the "Models" folder of your project. Once you've imported the model, select it and go to Edit > Object > Group. Name the...

I use this on KNO3+Sugar for 3d printed model rocket engines. ALWAYS mill these components separately as the impact from the balls in the mill can cause the mixture to ignite in the enclosed jar. When you enclose flammable things they tend to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

You Need: Raspberry Pi Model B or Plus can be purchased here. A 2-channel relay board will suffice; purchase here. Jumper cables are available here. Buy buttons here. Get a webcam from here. Acquire an SD card here. Power your Raspberry with a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

First off, thank you ohman74 for posting this fantastic Buster Sword What a great model to work with!! I wanted to make the materia in the sword light up and be replaceable. After searching for LED balls on Amazon I came up with this perfect...

This station involves three separate 3D printing processes:Main housing (220mm x 220mm)Rotating disc (172mm in diameter)Gears, gear holder, and "engine" stick componentsMotivationThe primary motivation behind this design was to facilitate the...

Perhaps my specific model of the C270 camera had some differences? Original "c270_hinge_M3_screw.stl" was missing a crucial constriction of the bore for the pin (as viewable in the original camera mount). The edge of it should form an inner lip for...

I started with the photos of the metal models (I've uploaded those photos to thing:1618843) and went from there. All the design work was done in Moi (Moment of Inspiration). Once I had an escapement design, I ran it as a simulation (unsuccessfully)...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

These two parts are rather small but also simple ball joint parts that rely on friction and cannot be tightened. For those of you that want a to be able to tightly secure your camera in a certain position, there are also parts that form a double-ball...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the pictures, the standard STL size...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...