df65 3d models

This is remix for camera mount on the rear deck of R/C sailing boat Dragon Force 65. I wanted to use thee waterproof case that comes with the SQ12 camera so I simply added a GoPro base to the original design. Kudos to him! ... The mount can be simply...

***Updated version of the DF 65 / 95 yacht stand.***\r\nhttps://www.thingiverse.com/thing:3248354\r\n\r\n\r\n------------------------------------------------------------------\r\n\r\nEnhanced printed tees, resized all holes to fit M5 screws...

https://www.thingiverse.com/thing:3391502 for DF95/DF65 https://www.thingiverse.com/thing:2139038 for DF65/RG-65 https://www.thingiverse.com/thing:3250906 for IOM Also, many thanks to David Jennings himself for sparking the fires of so much creation...

These arms will also work for a DF65 and about anything in between. Short Drill Jig- This is a good test print to make sure the long drill jig print will fit your PVC pipe. You will also use it to drill the holes in the small frame connector PVC pipe...

These tools will swiftly create precision-fitted patches for the joysway dragon force sailboat. ... Print Settings: Printer: Achatz easydelta remodeled Rafts: Not used Supports: Unused Resolution: 0.2mm print resolution is set Infill: 30% infill...

These versatile tools are extremely helpful in quickly and efficiently cutting reinforcement patches for the corners and mainsail luff from durable dacron tape. ... Cutting Tools Setting Your Printer Choose a Printer: Achatz easydelta remodeled model...

Wall stand for Dragon Force 65 with a Flysky transmitter (FS-I6 in my case)Should also fit most RG65 boats (also works with my Volantex Compass), and other Tx brands as long as your Tx top handle is wider than 75mm (inner width)Use 5mm screws or...

... a metal ring, providing easy access and preventing loss. Its sturdy construction ensures the key remains safely in place, even under heavy use. The DF65 keychain is an essential item for anyone seeking to keep their keys organized and within reach.

RC Sailboat masthead "crane" for 6mm mast. ... Made for a rig with DF65 A+ sails on a swing rig. ... 2 versions with 5mm difference on the foresail hole placement.

This is a trap to replace the sticky hatch of the Dragon Force from Joysway, the DF65. ...For perfect sealing, you can glue an air chamber tape (for example) all around it.

This is a very handy and sturdy frame to protect your Rudder if you carry it on its stand.I designed this for my Volantex RG65 Compass, but it should be flexible enough to fit any RG65/DF65 stand.Be careful not to set it too high on the stand, so...

***Note: This has been updated to an improved version (V2, 30th Jan 2019)*** ***Please use these files.*** https://www.thingiverse.com/thing:3391502 ----------------------------------------------------------- This is a remix of...

I have upgraded my Volantex RG65 with the DF65 A-rig sails, and it's definitely worth it! But I also found out that the mylar sails, not being in a textile material, are more sensitive to a less than perfect trimming.With mylar sails the top trim is...

And easily with few additional parts that I desingedYou can flip DF95 to side if wind is blowing too hard.Print with any material, PLA is fine, amny other is too.!“Side Leg”https://www.printables.com/model/284410-df65-stand-side-flipping-legand“Keel...

Also other materials is fine.Also check these other parts that I desinged to put your DF95 to side with stand when wind is blowing hard.Bulb support:https://www.printables.com/model/448698-df95-bulb-supportandSide...

Specifically crafted for the DF65 base model, this stand comes equipped with a cost-effective remote control. ...Please note that it is incompatible with the Fly Sky remote; I will upload an alternative version tailored to this particular remote in the...

Then try these adaptable enhancers that fit seamlessly onto the original DF65 stand. I specifically designed them with a distinction in mind for the bow and stern sections of the boat, making it easy to identify which one is which by simply looking...

For my DF65 hatches, check out https://www.thingiverse.com/thing:1666297 I printed this hatch at a 0.1mm layer height to achieve a thickness of only 0.5mm, resulting in at least three layers. This not only ensures it remains waterproof but also...

Inspired by the DF65 yacht stand, I decided to create my own version based on sakunamary's design from Thingiverse, which can be found at https://www.thingiverse.com/thing:2139038. For the International One Metre (IOM) class, I also drew inspiration...

The front mast position is suitable for swingrigs, while the rear mast position is ideal for conventional or DF65 rigs. Use iglidur JSM 0608-043 for the upper bearing and JSM 0405-04 for the lower bearing. ... To report any issues, visit...

:) ....But that stock part is still lousy.Long story short: I designed this new pivot mechanism, inspired from the DF65 "gooseneck" pivot, where the main boom is pivoted around the mast by that big and sturdy-looking part.This pivot is in 2 parts : a...

FAQ: https://thingiverse.com/shivinteger/about Generating Attributes Log: [0] Project Title: Yazzo UClip Hinged URL: https://thingiverse.com/thing:5545 Author: WilliamAAdams License: Creative Commons - Attribution [1] Project Title: GoPro Hero3 Frame...

Thing URL : http://www.thingiverse.com/thing:5929 Thing Author : sliptonic Thing Licence : Creative Commons - Attribution Thing Title : Duck Call Thing URL : http://www.thingiverse.com/thing:38359 Thing Author : jamesarm97 Thing Licence : Creative...

Then you can try these adaptors that fit directly on the original DF65 stand. I have designed them differently for prow and stern parts of the boat, which is which is easy to see since it's printed on them. Remove the bottom parts of the stand and...