diatone gt r349 canopy 3d models

This custom canopy is designed specifically for the Diatone GT-R349 drone model, extending further forward than usual to ensure complete visibility around its propellers. ...The design allows for printing with either flexible TPU or durable PLA...

##Canopy Diatone R249/R249+/R349/ER349/R369 You'll need: 4x screws M2 (between 8mm and 10mm) 2x screw nuts M2 2x screws M2 for micro camera 2x standoffs M2 19mm - original (or 20mm) 1x 3" frame compatible (GT R249/R249+/R349/ER349/R369) Frame R349: -...

##Canopy Diatone R249/R249+/R349/ER349/R369 You'll need: - 4x screws M2 (between 8mm and 10mm) - 2x screw nuts M2 - 2x screws M2 for micro camera - 2x standoffs M2 19mm - original (or 20mm) - 1x 3" frame compatible (GT R249/R249+/R349/ER349/R369)...

remix of a diatone canopy

Diatone GT-R349 and similar battery protector\launchpad. In comparison to the thing it is remixed from (https://www.thingiverse.com/thing:2588938) it weights approximately nothing - 8 grams. Needs to be printed with supports. ... Fusion360 archive...

Clean plate for diatone gt r349, compatible with umma85 and 95x parts.

I made this mount a while back for my Diatone GT R349 micro drone. It's far enough from the bottom mounted battery and it doesn't touch the frame at all. I don't think range is an issue with this kind of quad. I've never had any problems. I...

Diatones canopy is slightly too small to accommodate the DJI Caddx VTX so this was designed to hold the new antenna and arch over the VTX. Large cutouts around the camera were necessary for prop clearance and yes it does kinda leave your expensive...

This is an updated version of another canopy discovered on thingiverse. I have expanded the antenna holder to snugly fit the UXii or Foxeer Lollipop. Simply press it into place, and it will stay securely without requiring any adhesive. ...If you're...

This is the R349 Lollipop mount remixed for the Lumenier Micro AXII. ...Many thanks to KTMDirtface for the original and for including the f3d and step design files.

I've created two sides and one top plate for the Diatone GT M515 to safeguard its electronic components. The top plate is specifically designed to accommodate a Foxeer Lolipop. These parts were engineered with an ultra-light design, ensuring that...

The updated R349 Lollipop mount now seamlessly integrates with the Lumenier Micro AXII, a major breakthrough courtesy of KTMDirtface's ingenious work. ...A huge thank you goes out to KTMDirtface for generously providing the original design and including...

This custom TPU extension empowers users to securely install and shield larger cameras such as the Ratel on their GT-R349 (also compatible with R369 and R249 models). The standard canopy's camera protectors are woefully inadequate, leaving lenses...

Electronics professionals rely on Diatone GT R349 components to securely fasten battery wires, a critical capacitor, and essential antennas.

This POD/canopy is specifically designed for Diatone's GT-R90 drone, with carefully crafted areas that perfectly fit a whip antenna in the ridge and feature a Capacitor at the back to effectively eliminate video noise. The 24V, 220uF, low ESR...

Used in Diatone GT R349 to hold battery wires, capacitor and antennas Check more details from this build at https://rotorbuilds.com/build/22688

Remix from evret canopy with antenna lollipop holder and GTR90 text. Printed on TPU. ... See the make for images : https://www.thingiverse.com/make:607307

Remix from every canopy with antenna lollipop holder and GTR90 text. Printed on transparent plastic material. ...Check out the maker's page for images: https://www.thingiverse.com/make/607307

... I Never Fly Without a Battery-Powered Buzzer, and It's Saved My Life Often. This Version Accommodates a Full-Speed Lucky Box Beeper/Buzzer and a TBS Nano RX on a Diatone GT-R349 and GT-R369. ...Compatibility with the GT-R249 Has Not Been Confirmed.

... greatly. This is an Insta360 Go Camera mount for the Diatone GT R349 & R369. The camera angle can be varied. ...According to my testing, the Jello in the Insta360 Go's video is way less in this orientation as compared to the horizontal orientation.

This canopy serves as a cover for the R349 and comparable models.

Remixed an existing reciever mount to be just the antenna themselves. ...I'm using an FRSky XM+ tucked under the flight controller board and the antenna ran out the back.

... rabbit. You will get larger field of view and more crisp images without sacrifying your HD recording. ZX-RC warmachine canopy available for download. For more info and download: https://zx-rc.blog/2020/09/29/diatone-r349-r369-hd-canopy-upgrade/

This is an Insta360 Go Camera mount for the Diatone GT R349 & R369. The camera angle can be varied and detached from the quad when not flying. The camera mount provides protection to the camera lens. ...I wasn't able to find such a design on the...

Duct for R349 requires only removal of props for easy installation. Installing this duct is a straightforward process that doesn't necessitate the use of screws. ...Instead, you can secure it in place with a convenient zip tie.

Designed on TPU, this prototype boasts an impressively rapid development process that may not be its strongest aspect - I've yet to put it through flight testing.

I designed mine with a 0.7 layer height, which pairs well with my 0.8 nozzle, and I didn't add any supports since they're unnecessary for this model. To keep things lightweight, I went with 0% infill and walls that are approximately 0.8mm thick. If...

Simple, but sturdy antenna mount for the back of your drone. To install, remove the two metal posts at the rear of the frame, insert them into the mount, attach your antenna adapter and re-install them onto the drone. I do not remember what the...

I was on about my 4th flight when I unexpectedly collided with some unseen tree limbs, resulting in a rough landing that left one of my arms scuffed. Deciding an arm protector would be a worthwhile investment, I created this design using Fusion 360.

For optimal performance, fabricate the model on a TPU without any added support material. Construct it with a top-down orientation to achieve seamless integration of the Runcam Eagle Pro Micro camera system. To secure this setup, use M3 screws that...