digitakt stand 3d models
153089 3d models found related to digitakt stand.
thingiverse
A stand for the Digitone and Digitakt with a angle of 30 degrese. ...And a Xmen logo
thingiverse
Quick-to-print stand to raise your Digitakt by 4.5cm or 2.5cm. Minimum plastic, but sturdy enough to not be afraid to press encoders. ... The stand is attached with two 12mm M4 screws with the corresponding washers.
thingiverse
The stands can be mounted one the Vesa-Mount on the backside of a Digitakt / Digitone, or you can put (wooden/metal/plastic)-poles with a diameter of 1cm trough the holes, to prepare a "standalone-stand". It is very sturdy and you can transport it...
thingiverse
This is a Elektron stand for the Digitone and Digitakt combo. It's robust, I printed it with 15% infill, 2 perimeters. 0.2 layer height, printed with black Prusament PLA. I used M4 bold and nuts to attach the components together. There are...
thingiverse
Prototype stand for the Digitakt or Digitone specifically done for okam. Please note that I printed it with a brand new PETG roll, which I hadn't dialed in yet except for a heat tower. Yes, sometimes I am this stupid. :) If you have any...
prusaprinters
This will create a vertical stand for your Elektron Digitakt and Elektron Digitone combo. They are stacked vertically with this stand. Each printed as separate components and attached by M4 bold and nuts.</p><p>Required components to print:</p><p>4 x...
thingiverse
Uploaded a lifted stand for Digitone and Digitakt. The idea was to lift my Digitone behind my Rytm or other studio gear to save some space. The stand don't have to be screwed on, they are quite wide (3 cm) and won't fall over that easy. ...But mounting...
thingiverse
... want to print it on a FDM Printer you can stretch it to make it a little longer but it will also fit the Digitone quite nicely with the shorter length. This Stand is optimized for smaller printers and might be a little shorter than usual stands.
thingiverse
Fits Digitone, Digitakt and Analog Heat, in single or multiple configurations. Vertical multi-stand to come eventually. You can print these in - single-device configuration with "slim" side plates (5mm); this is not really recommended because it...
thingiverse
stands for synths and other machines (attached have 35degree) please inquire for other machine or give a hint thx
thingiverse
I also have printed [this stand](https://www.printables.com/model/321797-elektron-syntakt-digitakt-digitone-stand-25deg) for the Syntakt which looks awesome. Since i didn't want to put velcro on my beloved Syntakt in fear of residue when removing...
cults3d
... ... The stand is designed to make it easier to see and access the digitakt/digitone. The digitakt/digitone have standard VESA mount connections on the back. M4-18 Nice to be able to use one stand for two different devices. ... www.soundstand.eu
cgtrader
Digitakt 3d model of sampling drum machine from Elektron. created in blender. texturing done with substance painter and affinity designer. 4k pbr textures included. material setup inside blender for eevee and cycles, 37530 polygons all quads. ...
thingiverse
... I just glues the collars on the left into place. Once assembled I have a zip tie strung across the top putting downward pressure so that the Digitakt presses into the lip of the case, this keeps it from falling out when turned upside down. ...
thingiverse
... Charging board - https://smile.amazon.com/gp/product/B07JMY631D/ My voltage reader case - https://www.thingiverse.com/thing:4122686 More info on internal battery mod here - https://www.elektronauts.com/t/digitakt-modified-with-internal-battery/91600
thingiverse
Cover for the Elektron Digitakt. Six neodymium magnets 5mm x 1mm can be glued in to keep the cover in place for transport. The magnets sit on top of the screws so the cover does not scratch the front plate. ...
thingiverse
A 2mm thick cover for the Digitakt (it probably fits the Digitone as well). It can be kept in place with a strap. ... I personaly use it with a amazonbasics gopro bag (L) : ...
prusaprinters
A 2mm thick cover for the Digitakt (it probably fits the Digitone as well). It can be kept in place with a strap. I personaly use it with a amazonbasics gopro bag (L) :...
thingiverse
Thanks to laikrodiz for the idea: https://www.elektronauts.com/t/digitakt-modified-with-internal-battery/91600 Requirements: -Print STL FOUR TIMES. You could also do it with just two and more tape I guess? -six 18650 batteries. High capacity, low...
thingiverse
... internal battery mod. Uses 6x3mm neodymium magnets on the bottom. Voltage reader used - https://smile.amazon.com/gp/product/B00C58N9O4/ My battery frame for Digitakt/tone internal battery mod - https://www.thingiverse.com/thing:4122683
thingiverse
Built a taper into the design so if printed with the face adhered to the print bed, this should barely fit onto a 220mm wide bed. This print was broad enough to start warping, even with PETG, however it didn't affect the outcome enough to matter.
thingiverse
This is a remix of https://www.thingiverse.com/thing:4715880 Modifications to original design: - Split in half to fit on smaller print bed (e.g Ender 3V2). Also allows customizing each half to be a different colour. - Added two circular...