dishonored folding blade 3d models

THE BLADE Corvo Attano

The Folding Blade is a unique sword and the primary right-hand weapon for Corvo Attano and Emily Kaldwin in most of Dishonored and Dishonored 2. ...The only gameplay difference between this and other swords is that it can be upgraded.

folding knife blade

In order to be successful in using a pushing folding CAM propeller it might be neccessary to ascertain that the folding blades are partially restricted in how much they can fold both forward and backwards in order to not tear into the wing. Or hook...

This is my model made from screenshots and artworks of Twin Blade Knife from Dishonored: Death of the Outsider. To put the model together you'll need 10mm x 2mm x 80mm (or close to it) ice cream sticks. Some pieces must be glued together (Handle 5...

This handy folding blade holder makes using the blades easier and safer. It has an integral clip for locking the blade in securely, and it also has two storage slots in the handle for fresh blades. CAUTION: Be very careful when handling and using...

This handy folding blade holder makes using the blades easier and safer. It has an integral clip for locking the blade in securely, and it also has two storage slots in the handle for fresh blades. CAUTION: Be very careful when handling and using...

Folding blade knife ball bearing

I thought that this would go well with the mask I uploaded.

This full scale, fully functional replica of Corvo's blade from Dishonored is based directly off of the in-game model. The only major difference is that the blade had to be shortened to fit inside the handle since the blade shown in the game is...

This full scale, fully functional replica of Corvo's blade from Dishonored is based directly off of the in-game model. The only major difference is that the blade had to be shortened to fit inside the handle since the blade shown in the game is...

Whole thing is slightly bigger but it still fits nicely in the hand. My remix of super cool design I found here on Printables: https://www.printables.com/model/57207-folding-karambitVideo:...

Just press on the rounded part of the handle to unlock and fold the knife (the play between the handle and the pin is reduced for a good holding without glue, you'll have to force a little to clip in! )sand very lightly if necessary... Easily...

Motor wire holders - I need a way to keep the wires neat and free from pinching during folding. For assembly you will need to use some force but not to much because you will break the frame. I've put together several of these so far and only had one...

Tacblade Utility Stanley Blade Folding Knife Remix Verfeinerter Version der super Vorlage.

ring with symbol from dishonored

Insert a standard utility knife blade into the blade holder and secure by threading an M3 x 10mm screw into the plastic. To close the knife, push the liner lock out of the way and fold. How I Designed This Designed in SolidWorks. ... Inspired by the...

lock designed to prevent patio umbrella from spinning around when tilted to block the sun. designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is...

It is easiest to carefully force the knife open slightly further than full open, which should break free the blade holder from the liner lock feature and the pivot pin. Insert a standard utility knife blade into the blade holder and secure by...

The motor shaft can be 3-3.2mm or 4mm (requires drilling after printing) If you decide to print the blade use 1mm shell and 100% infill. Print spanwise so the leading edge touches the printing table, minimal supports will be needed It is secured...

This is my folding knife design for disposable Stanley style blades. Its a hybrid between a friction folder and a flipper. Designed for the UK so no lock, but is very stable in the open or closed position. 100% printable, the bolt best at 0.12mm...

This logo comes from the video game dishonored, and is sized like my other rings.

A coin with the mark of The Outsider and a Bone Charm from the game Dishonored!

This logo comes from the video game dishonored, and is sized like my other rings.

These Pendants are designed after the Outsiders Mark and Boncharms which are found in the game Dishonored

This is fan art for the game Dishonored. Made in Blender 3D. STL Format. There are 4 files in the archive. ...The model is divided into 3 parts.

Some Chaos and Momentum tokens made for the Dishonored TTRPG by Modiphius. Thought these may be nice physical props in place of the recommended d20s in the rulebook. ...Designed to look similar to in game currency shape.

This is the wristbow from Dishonored's DLC.  This consists of the base wristbow and a set of rails that should fit into place.  Print it flat on the bed, at least 25% infill, and with a raft or brim. ...(arrow and side tube are not included in the...

Hi guys This is a project that I worked on over the weekend, he’s a fan of Dishonored based on the wonderful work of Cedric Peyravernay and the lovely work of modeling and textures of Miki Bencz whose work in textures has me in love, I hope it’s his...

The time for choosing the LC for the second month of work coincided with the time when my hands reached for the passage of the fresh stealth action “Dishonored 2”. The game made a very strong impression (especially in visual terms), so I wanted to go...