diy power pack 3d models
197043 3d models found related to diy power pack.thingiverse
V1 was an Prototyp that i was created in the Video V2 is without usb and switch. ...that i created for a friend all infos or article are on Youtube Video description.
thingiverse
How to make 20000 mAh Fast Charging Power Bank (DIY Power Bank Fast Charger)
myminifactory
I print a Case for my DIY Power Supply Bench, have fun with it.
thingiverse
More details at: http://www.roroid.ro/dps5015-diy-power-supply/ Video at: https://www.youtube.com/watch?v=0fAxZjIAwfI
grabcad
Doepfer DIY Power SupplyI'm not an expert in 3d-modeling but dimensions are correct and it should be good enough for designing a eurorack case.
thingiverse
... for this project. Englishhttp://www.instructables.com/id/Handy-Power-Supply/ Chinesehttp://regishsu.blogspot.tw/2016/03/handy-power-supply-diy.html#more If you find my design interesting, you could make a small donation:http://paypal.me/RegisHsu
thingiverse
(You'll need a lot of each part, except for the completed power cord) (Like the Sonic Screwdriver, the 3mf files are life-sized) Print Settings Rafts: No Supports: No Resolution: As High as Possible Infill: 100% Notes: Edit whatever you'd like and...
myminifactory
This is DIY Wireless Power Bank with : 1. 6000mah Lithium battery2. ...Wireless charge board...
thingiverse
This is DIY Wireless Power Bank with : 1. 6000mah Lithium battery 2. ...Wireless charge board :...
grabcad
A simple version of a power hammer for a diy project, i tried to do a simple simulation but the spiral cut is giving me issues with it so i left it alone for now. ...The project is pretty simple, a motor turns the spiral which pushes the arm up which...
grabcad
2nd version of a diy power hammer, quite a simple working process, pressing on the foot rest tightens the belt and starts the power transfer.NOTES: Missing holes and bolts for fixing the electric motor in to place.The back wheel part that is...
thingiverse
... and switching board wiring instructions from the supplied manuals. ... Fit the power module, board , fan regulator and fanon the corresponding holes and screw the 3M screws Voila you can now enjoy your DIY Power Supply (: Please share your makes
thingiverse
This is a DIY power supply box that I made. The back panel cut outs are for a 50mm fan and 120V IEC plug with switch. The front panel has cut outs for a LED, 2 USB, positive and negative jacks, small on/off switch and buck boost module #XYL3606. The...
thingiverse
I decided to make a DIY Power Bank using laptop batteries. This is a simple case. It holds 12...18650 Li-on batteries. I wired them in parallel. Below is the link for the circuit board I used. Read notes below. Overall measurements...
thingiverse
In order to assemble that you need 3x18650 batteries and DIY PowerBank module from aliexpress: http://ali.pub/2tfbm6 SolidWorks assembly packaged and attached as zip.
thingiverse
A compact DIY power supply based around the DPS5005 module. **Specs** - Output voltage range: 0 - 36 V - Output current range: 0 - 5 A **Required hardware** *Electronics* - [DPS5005...
grabcad
Wood based half power rack that can fit an Olympic bar. ...The rack pivot against the wall to occupy limited space when not in use.
thingiverse
Parts: - computer power supply - digital voltmeter https://www.ebay.com/itm/DC-0-100V-10A-Dual-LED-Digital-Voltmeter-Ammeter-Voltage-AMP-Power/181991348992?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 - step up/down power converter...
thingiverse
Took dittohead's 4 AA Battery Holder and decided to make it a power pack. Tom Hanks to dittohead! Wiring this turned out to be a little abstract, and was fun! Huzzah! Please, though, if you're wiring this yourself as I did, make sure no...
thingiverse
I also have a YouTube video that shows more of the design and features of this power supply: https://www.youtube.com/watch?v=MtTcv4PDfNw Link to the module on Amazon:...
myminifactory
I already have one desk-top power supply bought from amazon for just little bit more money than this project but where the fun in just buying pre-made stuff. I got started on the project after seeing Dronebotworkshop youtube videa on this very...
thingiverse
For this, I used 3 6,000 mah 18650 li-ion batteries(for a total capacity of 18,000 mah) and a usb and micro usb board to charge the batteries and to charge my phone with the power bank. I made this case to fit 3 of those 3.7v batteries and there is...
thingiverse
Solar power charger enclosure. Houses two 18650 battery holders, a TP4056 charge controller and either of a MT3608 (For up to approx 30V DC) or a USB boost converter (For 5V USB). There is a blank top also for a more compact assembly when not using...
thingiverse
This is a DIY single 18650 rechargeable battery pack to charge 5V gadgets. The case cover comes with slide function. Use "Flexing battery holders 18650" from Heinz Spiess... (thanks for that :-) Which fits perfectly in my case. Use little hot glue...
grabcad
Why buy an ice pack specifically for a certain part of the body when the DIY Ice pack can be secured with practically any form of rope or cloth lying around. There is no hassle when trying to clip it either, because the finger holes allow for one...