dji fpv goggles analog mod 3d models

When I Get the MMU Going, I'll Update the Firmware Mods Listed Below as Well. The Only Other Hardware Modification Was to Open Up the Wire Pathway in the Extruder Back Cover Slightly. A Small Drill Bit (About 4mm) Was Used to Clear Two 4mm Nylon...

Hermit Crab mount uses 2 3x8mm bolts to secure to mount plate Orbiter mount uses 2 3x12mm bolts to secure to ender mount (2) 3 x 8mm bolts for bltouch mount (2) 3 x 40mm bolts for duct ~20 Threaded Inserts (M3x4x5mm) 60mm PTFE Tub - [M3 x 4 x 5mm...

These parts serve as direct replacements for some components found within [InMoov Chest by Mindless](https://www.thingiverse.com/thing:2175499) and [InMoov Torso Mods for the XBoxOne Kinect by...

I've included .Step files so you can mod the file or cut up the model for test print purposes. If you do not want to do that yourself, I'd be happy to upload. my test prints - which were for the Nano housing, usb module and bearing fittings. For the...

I also have gone all the way down to bottom, converting to a full-independent double wishbone, plus lot of many other mods. However, after many years of trial-and-error, I kind of came to certain balancing point, where too much modification is not...

This is a remix of https://www.thingiverse.com/thing:4057643 ( original reddit post ) I remade it with OpenSCAD to allow customization, by modifying only a couple variables. It will generate a STL with dust filter side laying down for easier...

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace extends your Anet A8 Plus in the X and Y directions by 40mm, providing stability to the frame and sufficient space for a 330x330mm hot bed surface....

https://www.thingiverse.com/thing:5454140 https://www.thingiverse.com/thing:5454048 You can of course swap out parts with the US version as I think a similarly modded version would look fine in the US as well. (link:...

I am not making any money with my design, and if Prusa wants me to take it down, I will.All of which to say - if you like this design, better download it now.----------------------------------------------A very simple mod of Neon22's Customizable...

I have credited where I got the mesh I modded from. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20% Notes: Sliced with slic3r prusa edition 1.39.1. Custom Section Fits if your...

Like I said none of these really do fit as when you have to scale them when slicing it comes out of proportion and its not working. I had a specific Power rocker switch with fuse that I wanted to use. So I designed this very crudely but very...

This mod works only together with high legs that rises printer up to make enough space to fit thick PSU. Front riser feets source: https://www.thingiverse.com/thing:4851027 (I modify it lilbit). Big thanks to autor. INSTRUCTIONS: • Disconnect...

I edited the model once more to add the threads and some other mods to make sure it can be printed without supports, printed again, and tested fitment. Thumbs up!! I'm going to try and see if I can link a video or two of the installation and the...

Info: This is a "tophat" mod for the "Ncase M1" case to improve airflow and/or mount an AIO at the top of the case. There are currently several different sizes of the tophat, so make sure you have selected the proper height of the model before...

Don't remember exact lengths on this set of hardware.The Low COG battery tray is designed to give you the clearance needed for the skid plate mod as well as lower the battery tray 10mm and the esc tray 20mm to lower the overall center of gravity for...

SUPPORT If you found interesting and useful, consider donating (for material filament, coffee, chocolate, and accessory parts for designing new mods). https://paypal.me/Deen0XEOL Please leave comments, feedback, and/or photos of your makes. ...

This is a mod of my [Smarthub Enclosure for Raspberry Pi Home Assistant Build with Official 7" RPi Touchscreen](https://www.thingiverse.com/thing:4903108) meant to be used more as a tiny desktop. It's got room for a 40mm fan and 3 panel mount USBs. ...

Original claw modded so it push fits into the last segment on the leg. Use either elastic or a wire as the core. Create a "knot" on one end, then thread the segments onto it. 14 segments and one interface joint. The claw will push onto the end of the...

The case is made for a flex-ATX psu and I personally used this one: https://a.co/d/hRQnHkV (it has proven to be a good PSU, I just did a mod of replacing the fan with a noctua fan cause the original one was quite noisy. Also it is a bit cramped while...

Unfortunately the mods of this site were not good mannered enough to inform me and do not seem to want to rectify the issue so I have republished without any quality references and deleted the original. Any way rant over, hopefully available again...

Here is my minimalistic CR10's hotend cooling mod. It uses the stock part cooling fan and also the original 40mm fan, which I have replaced of course with Noctua's high-performance fans. Airflow has been thoroughly tested and can be seen in one of...

So understand that the work is always about to be finished.I leave you my Discord channel, if someone wants to join to give an opinion to improve the system, know how to place the plate that is behind the wheel inside the base or simply to talk about...

This is a mod of my Rasptop 2.0 Laptop (https://www.thingiverse.com/thing:2859679) to create a pretty rugged mildly water resistant if built correctly tablet computer. It uses a lot of the same parts as the Rasptop 2.0 including the 7.2 volt 2s...

You will have to remove the top plate and Vista to do this mod, but it's not difficult at all and only takes a few minutes. You may have to desolder the XT30 or desolder the power lead from the FC to thread it through the mount, as with the...

This mod eliminates around 80-90% of the wheel plate flex on a Playseat Challenge. The glove box is really cool, but optional, if you don't want it just print the right arm twice. See before/after video here https://youtu.be/5B6NBgwF4yE ...

As i couldnt find an interior for the 1/10 model, i modded this one to fit his big brother.It can be klipped into the body (can be fiddly), no screws or glue needed. There is enough space for my 9000mAh 3S Lipo underneath.I omitted the steering...

-25-30% weight.Be aware that it is a free mod.I am not responsible for any damage or harm you do to yourself or your parts ;)Weight: 9.4gr base, 2x 1.7gr mousebuttons, 3.23gr scrollwheel pcb, 5.18gr main pcb = 21.21 gr (PLA) . ...There is still huge...

The basic idea is you run your cables from your AV mod out the hole in the 2600 and thread it through the box. Next, solder up the jacks. Then assemble the box itself with screws. Lastly, use the clip to secure the box to the 2600's case. Use hot...

Remember that this mod is not supported by Ultimaker and the original firmware will not work correctly with this setup.I have uploaded an adapter for a bowden setup where you can screw in a M6 bowden coupling, furthermore there are an adapter for the...

The holder for pen was designed to hold a pen, pencil, or marker to use the 3D printer as a plotter similar to pascalmakes plotter mod but is closer to the original extruder location so more of the bed can be used. The Gcode files for using the...