drum rack clamp 3d models

I designed this to mimic the clamps included with a Roland V-Drum electronic drumset, but I think it could also work well with an acoustic drum rack that uses standard 1.5-inch round tubes. ...The holes for the bolts and nut traps are sized specifically...

Check out one of the pictures showing the little white layer between the clamp and the rack; it provides a good grip on the drumrack. Without it, I had some issues with not being properly fixed on the drumrack. There's also a screw-handle for a...

This is based on a drum rack clamp from a Roland electronic drum set. The clamp joins two pieces of 1.5" tubing together and should work with any brand of drum rack that uses standard round tubing. Two drum lug screws, each 1.5" long, and two 12/24...

This is an accessory for the vertical side tubes of the Alesis Nitro Kit Drum Rack, which can be easily turned.

Musicians expertly assemble drum equipment organizers.

... I connected this pad as a quad trigger to a Roland TM-2 trigger module and connected it with the self-made rack clamp to my e-drum rack. Principle: The necessary sensors are easy and inexpensive to buy in online stores and the wiring is a breeze.

Made some change to the model to use Drum Tuning screws and 7/32 nuts The joint is made with an M5 screw and auto lock nut Can be used with the same connection of the original model

This is a T for roland drum rack (hardware), for 38mm tube Print this model stand up with automatic supports enabled everywhere (not just on plate) Use 30% infill min, and résolution of 0.2mm Happy printing drummer's ! ... David.

This is a T for Roland drum rack hardware, designed specifically for 38mm tube. Print this model standing upright with automatic supports enabled throughout (not just on the plate). Use a minimum of 30% infill and a resolution of 0.2mm. Happy...

Insert to reduce internal diameter of standard Roland Drum Rack clamp provided with the MDS-4, MDS-9 and MDS-12 racks from ~22mm to ~20mm to accept tube of typical Microphone stand vertical tube.This object was made in Tinkercad. ...Edit it online...

Drum Clamp is used with crane or fork lift to lift drums .. ...clamp have two suspending positions

I'm revamping the Roland Drum Rack Clamp, and this hybrid concept turned out so great that I've chosen to leverage its design as a foundation for mounting my Alesis Sample Rack instead.

The diameter is the same as most drum racks, 1-1/2" The Tube with the smaller bar attached, is designed to fit most drum rack clamps. (see photos) you will need to assemble a simple piezo setup and double stick it inside the larger tube on the...

This is my inaugural blog post, and today I'll be demonstrating how to craft a rack-style drum module for the popular Arduino-based MIDI drum project.

Roland electric drum clamp. ...Pla works but petg is better

Fork-mounted drum clamp. ...Захват бочек на вилочній погрузчик Захваты бочек с монтажом на вилах Захват на две бочки

Fork-mounted drum clamp. Захват бочок на вилочний навантажувач. Захват бочок з монтажом на вилах. ...Навісне обладнання від ТМ Agri Advantage

A headphone hook for horizontal 1.5" (38.1 mm) drum rack tubing, the common size found on Roland e-drum racks. You can choose between two designs: one labeled "Headphones" in writing and another with a simple icon. The hook clamps onto the tubing...

The bolts and wing nuts are M6 Possibly the material you print the clamp with will require a bit of extra filing or sandpapering. Please note that the inconsistencies you see in the picture will NOT be visible in the actual print, fortunately,...

This is a clamp designed to attach securely to a vertical drum stand (cymbal stand). In one of the photos, I showcase a triangle and hand chimes that are carefully hung from a knob. This project was created as a solution to that mess. I ultimately...

These clamps are for securely mounting a Drum Fan to a surface. 4 clamps recommended. Mounts with standard 1" or 1.25" deck screws. ... Works with the rolled steel rear edge on these 2 fans (17.375" diameter) Caterpillar FAN:...

An equipment holder for drum racks. The mount can be tilted by about 50° up or down. The rack diameter is in the file name (28.6mm = 1.125", 38mm = 1.5"). Other diameters may follow. The hole distance on the base is 50mm. ... Required: 5 M3 nuts 5...

100mm extension for electronic drum rack, definitely works on Alesis Surge. I expanded my electronic drum kit with a 2nd floor tom and 2nd crash a while back, it was great but really cramped. I started learning CAD recently and it dawned on me that...

I designed this to clamp a 15 mm "support rod" to the 35 mm leg of an Alexis Nitro Mesh kit. The centre bolt can be loosened with a hex wrench to allow you to change the angle (can't be adjusted while attached to the 35 mm leg). The swivel has 15°...

 This clamp holder can accommodate c-clamps, f-clamps, and pipe clamps.Simply print out as many dowel supports you require , slide them onto a ¾'' dowel and then mount it onto the wall. Ive had all the clamps in the photo on this rack for over a year...

But let's face it, you can have too many clamps - until that moment when you desperately need somewhere to stash them all. So why not take some scraps of 6mm or 4mm wood and craft a few of these? I've got an abundance of hanging rails and S hooks in...

This is a spherical joint that clamps into an existing Roland drum rack (for e-drums) component. You can use this to position a non-Roland component. I've used it to make a laptop mount on a treadmill, hold an iPad, etc. The spherical ball has a...

Made this for the 36mm open hole in the top of my electric drum kit rack, fills the hole nicely.

Adapter for mounting 1.5" drum rack mounts (e.g. Command, Surge, DM10, Forge, etc.) onto approx. 1" Alesis drum racks (e.g. Nitro or Turbo). ...For example, mounting an Alesis Command module with its mount onto an Alesis Nitro rack (see images).

Printer Details Manufacturer: MakerBot Model: MakerBot Replicator 2 Rafts: Optional - doesn't matter either way Supports: Yes Infill Percentage: 20-25% Printing Notes: To print the clamp successfully, place it on its side with the drum stick holder...