duplicator 7 1 5 3d models

FRC Gearbox 7.2:1-3 Falcon motor-1/2 in hex shaft

Customized version of https://www.thingiverse.com/thing:5397832 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5397832

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: pulley_b_ht is set to 8 mm additional_tooth_depth is left at 0 mm idler_height is adjusted to 1.5 mm idler is turned off motor_shaft diameter is...

Basic Square SLR Camera Mount Measures 1.7" x 1.7", Featuring Tripod Interface for Secure Positioning. Compatible with Most Makerbots, Offering Flexibility in Printing Settings - High, Low, or Medium Default Options Available. ...Optional Raft Suggested...

7 1/4 blade holder, to keep all your saw blades in one spot.

1.8"" (55mm) 7 segment displayA1801X G/Whttps://www.aopled.com/AOP_PDFs/CA1801G_GW.pdf

gopro hero 9 inclinazione 7 gradi Cactus 5" / 6" / 7" e shockwhoop

AOS Falcon 7 GoPro mount for the Hero 5, 6 and 7.

#Wanhao Duplicator i3 - Marlin bugfix 2.0.7.2.x - BIGTREETECH SKR 2 + TMC2209 + TFT35-E3.0 V3.0 by TheAlexClavijo This is a custom version of the Marlin Firmware for the Wanhao Duplicator i3 with Bigtreetech SKR 2 board, including firmware for using...

This is an axle stand for 1/7 scale Arrma or any other R/C with 17mm axle studs. ...

Human Interface Module: Deployed 20 Connections, Advanced 1.5 Pitch Surface Mount Pin-Header Configuration

This is a case for a 4x 7- segment and a single 7 segment (5 digit). It is used for DIY and prototyping. I used a header connector inside the case to solder wires from the segments. This exposes them externally from the case. I used a hot glue gun...

Request to alter for 5/16-18 UNC threads.

A simple phone case for the Nokia 7.1 phone. ...The one in the photo used 0 top &amp; bottom layers &amp; a hexagon infill to create the pattern.</p>

1.875" diameter hole saw. ...1-15/16" cutting depth, two alignment pin holes mate up with 5/8-18" arbor threads. ...Clearance holes on side to remove 1.75" dia plug.

-World of Tanks This is a 1-100 scale IS-7 tank. There was a lack of IS-7s here so I decided to post one here. The machine guns and the turret are one file but printed separately. The hull is the usual. To see my other designs go here:...

Print List: 2 x Z motor mount 2 x Top frame bracket smooth rod 2 x y bed end axis 1 x endstop mount 1 x endstop mount y 8 x bracket (this piece should be metal, but thick plastic can suffice until you can order something similar from Misumi/etc.) 4...

... part of a wellhead assembly, that helps to support the tubing string. ...The lower flange is 7 1/16", which attaches to the appropriate wellhead spool, the upper is studded to fit a 2 1/16" flange to which either a valve or end cap can be attached.

iFlight XL 5/6/7 Hero 6/7 GoPro Mount. Mounts securely on the iFlight XL 5, 6, or 7. Compatible with GoPro Hero 6 and Hero 7 cameras. ...Features a strong 25-degree angle, 5mm foot design for a stable hold.

7" LED headlight for cars or 4x4

A customized version of the design can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=49597 with specific dimensions including Small End Diameter of 15, Wall Thickness of 1, Top Band of 7, Large End Diameter of 80, Bottom Spout...

A Sleek Phone Case Designed Specifically for the Nokia 7.1 Smartphone. ...The model showcased in the image employs a minimalist approach, utilizing only the top and bottom layers of the case, while incorporating a hexagonal infill pattern to add texture...

What you get: three part beadlock wheel for Tamiya 1.7" FAV/buggy champ front tires to use as non driven wheel for trailers or Tamiya chassis as SRB or FAV What you need (per wheel): 2x 5x10x5 bearings  6x M2x6 countersunk screws for the beadlock...

Improved back cover for wanhao duplicator i3 2.1 printer with 80mm fan

EFR32 MG12 PBGA-125 Surface Mount Chip featuring 125 Balls, pitch of 0.5 millimeters, length of 7 millimeters, width of 7 millimeters and height of 0.87 millimeters.

The daughterboard I designed (V1.1) required some adjustments to fit through the reset and erase button holes found in other enclosures, so I started from scratch to create a new design. Other available enclosures lacked slots for memory cards or...

http://www.thingiverse.com/apps/customizer/run?thing_id=656884 Instructions Using the following options: BoardVersion is set to 1.1 Overhang relief is optimized at 10 units Lip thickness is set at 1 unit A lid is attached to the top of the board...

DEGSON DG129 Series 5.0, 5.08, 7.5 and 7.62mm pitch terminal block packAll sizes and types + Source files.• Current rating: 20 A AC/DC• Voltage rating: 300 V AC/DC• Temperature range: -40 ~ +105• Applicable wire: 26-12AWG UL (0.5-2.5 мм2 IEC)Types:•...

DEGSON DG129 Series 5.0, 5.08, 7.5 and 7.62mm pitch terminal block packAll sizes and types + Source files.• Current rating: 20 A AC/DC• Voltage rating: 300 V AC/DC• Temperature range: -40 ~ +105• Applicable wire: 26-12AWG UL (0.5-2.5 мм2 IEC)Types:•...

I'm Running A Quick Calibration Check Using The Standardized 1.5 By 1.5 Cube To Verify Your Machine Is Precisely Aligned And Functioning Within Optimal Parameters.