e3d edge filament
269758 3d models found related to e3d edge filament.thingiverse
This thing will allow you to route the filament around the edge of the table without risking to break or kink it. The top hole is at around a 15 degree angle from vertical, and the bottom (exit) hole is at about 45 degrees. Both holes are heavily...
prusaprinters
Rather than twist or contort the loose end of your filament to hold in-place by hole locations on the reel, this clip provides a simple way to clip and un-clip the loose filament during storage. The clip fits onto the edge of the spool reel. The clip...
thingiverse
The clip has been optimised for a spool reel with a 4.0mm rounded edge and tapers away from the edge, as implemented on the 3DFillies filament brand. Other filament brands may fit well, too (there are so many brands!). In most cases, you can...
cults3d
On one hand it is harder to load because it is in the back, but much easier to load because you are pushing filament through a lot less tubing with many less bends so is a net win in my opinion. ... the scad file is parametric so sholud be easy to...
thingiverse
On one hand it is harder to load because it is in the back, but much easier to load because you are pushing filament through a lot less tubing with many less bends so is a net win in my opinion. ... the scad file is parametric so sholud be easy to...
thingiverse
Modded, because mine was catching between the edge of the bearing and the guide itself, now should always stay away from edge
prusaprinters
Disc shaped nozzle holder with labels. 15mm thick by 75mm Diameter with knurled edge. Space for 10 nozzles into threaded sockets. Print instructions.gcode file is intentionally face down for a smoother top finish. .gcode has 2 pauses for color change...
thingiverse
ANYCUBIC Kossel Delta E3D V6 Filament Cooler Double Points
thingiverse
Hold brace for printer E3D Nano. ... Use filament holder from https://www.thingiverse.com/thing:3020026
cults3d
This is a remix of the rsilvers E3D v5 filament drive. ... Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend.
thingiverse
This is a remix of the rsilvers E3D v5 filament drive. ... Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend.
prusaprinters
This is a remix of the rsilvers E3D v5 filament drive. ...Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend.</p> Category: 3D Printer Parts
thingiverse
Umbau Ender 3 oder Cr-10 mit E3D Titan Extruder und Filament von oben .( zb Ikea Lack ) Benötigt wird noch ein einfaches 608ZZ Lager . Für den Druck wird folgendes benötigt: 1x Filament Umlenkung Titan Extruder 1x Ring 2x Spacer Die Montage...
thingiverse
Das Teflonschlauch-Ende mit einem Senker oder Messer innen leicht anfasen, damit das Filament leicht in das Schlauchstück läuft. Für einen Filament-Wechsel muß man dann ca. 50-52mm Rückzug einstellen Have Fun :) ENGLISCH This is a dual adapter for...
thingiverse
Print/filament cooler for delta end effector from Robotdigg, E3D V6 hotend (chinese clone) and 40mm fan. Works with stock 30mm hotend cooler. Need one M3x16 screw to fix it to the effector (hole in the effector is threaded). here, which has more...
thingiverse
E3D Holder with Filament Cooler for Falla3d Open Source Printer I needed to attach the E3D to my Falla3d printer, but at the same time I wanted to cool the filament. The difficulty was staying within precise space limits at the front and the sides of...
prusaprinters
This is an insert to replace the filament guide between the hotend and the filament gear in E3D Titan Aero to better control flexible filaments. I bought a direct drive Titan Aero to work more with flexible filaments on my railcore 2 build. This...
thingiverse
This is an insert to replace the filament guide between the hotend and the filament gear in E3D Titan Aero to better control flexible filaments. I bought a direct drive Titan Aero to work more with flexible filaments on my railcore 2 build. This...
thingiverse
This is a filament sensor mount/housing I designed to work in conjunction with the Petsfang E3D v6 Hotend and Titan Direct Extruder setup, but I am betting it could be used other places. I am using this with my filament mounted on the top of the...
thingiverse
Simple bracket that fits 2020 extrusion alows you to have a bowden tube guide to your E3d Titan, Designed to use a m6 tube fitting so top hole is 5mm you will need to run a m6 tap through if any one wants one with a different hole size just ask. To...
thingiverse
This is a mount to attach a Duet3d filament sensor (https://duet3d.com/wiki/Duet3d_Filament_Monitor) to an E3D Titan (https://e3d-online.com/titan-extruder) when used in a bowden setup. It replaces the aluminium bowden adaptor and places the sensor...
thingiverse
## Introduction __Replacement Filament guides for E3D Titan.__ I was having problems printing flexible filaments, with the filament getting squeezed past the hob gear and bunching up. This was caused by the excessive clearance between the injection...
thingiverse
When installing the E3D hot end, it is suggested to drill out the 'filament hole' beneath the hobbed bolt so the PTFE tube can be cut just under the bolt. While this worked OK, I had reliability issues. The problem is that printing with Flex is...
thingiverse
I wanted to convert my E3D Titan Aero from 3mm to 1.75mm filament. I knew you needed a new filament guide, and heat break, but also found out you need to replace the heatsink lid becaues the heat breaks are not the same. I ordered a fliament holder...
prusaprinters
I wanted to convert my E3D Titan Aero from 3mm to 1.75mm filament. I knew you needed a new filament guide, and heat break, but also found out you need to replace the heatsink lid becaues the heat breaks are not the same. I ordered a fliament holder...
thingiverse
It also has roller bearing filament guides to route the filament from the back of the machine 180 degrees to the input of the extruder. Also included is a ball bearing guide that sits under the spool to reroute the filament 90 degrees toward the...
thingiverse
It is attached with four 3mm screws to the original E3D fan adapter. ... Print Settings Printer: Delta Q remake Supports: ...
thingiverse
... part off my Bigbox and remodelled it. The component could be 3d printed with little issue as opposed to acrylic or wood cutting. Credit to Greg Holloway @ E3D, just remodelled and uploaded to be helpful just incase anyone needs a new one quickly.