easythreed nano 3d models

 # My Easythreed X1 config for Prusa Slicer Although created for Easythreed X1, it should also work well on Easythreed X2, Labists X1, SONDORY PICO...

EASYTHREED X1 may require modifications or Arduino settings to work properly. The programmer behind this source is not an expert, so further questions regarding the source code cannot be handled. It's hoped that a real programmer will improve this...

Mounting TBS Unify Pro Nano and Crossfire Nano on a 30x30 frame, stacking a 20x20 board on top.

НА русском. С английским я дружу весьма относительно потому сначала кратко на русском, а потом на английском. Сразу предупрежу всех ОБЯЗАТЕЛЬНО ПРИ ПОКУПКЕ ДАННОГО ПРИНТЕРА ПОНИЖАЙТЕ НАПРЯЖЕНИЯ НА ДРАЙВЕРАХ и прикрутите хоть какой-то кусок алюминия...

The fan duct for the X1/X2 comes in pre-sliced gcode designed specifically for printing on the X1. I printed it out on my X1 but was disappointed with the quality, so I converted the gcode back to STL and removed all supports to enable printing in...

The original had to small of a size so the controller would fall off it very easily. This upgrade adds a bigger (9.5 cm long) bottom plate that sits at a 2 degree angle so if you accidentally push the device it will want to move to the printer's side...

Its a remix of https://www.thingiverse.com/thing:4721861 X bracket with some little tune. !!!Not needed to print o purchase 12-14 teeth pully!!!!, i take 16teeth (100steps in firmware) but you need to little enlarge(1-2mm) holes for belt in...

The original had to small of a size so the controller would fall off it very easily. This upgrade adds a bigger (9.5 cm long) bottom plate that sits at a 2 degree angle so if you accidentally push the device it will want to move to the printer's side...

this should slide snugly onto the top of your z axis support to provide a filament guide for a spool of filament situation behind the printer.

Layer thickness 0.2mm

sometimes the cable that goes to the hotend, used to get into the limit switch of the Z axis, with this device this is avoided, it is the first version and therefore perhaps it is not quite fine, that's why see the images, already I use a safety tie....

On my X1, the base plate of the Z-axis is broken where the motor is on. So I quickly constructed something that works. No original spare part! ... If your printer also comes from China I will give you the OpenSCAD script so that you can change the...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6vAWWUiu1Hs

this should slide snugly onto the top of your z axis support to provide a filament guide for a spool of filament situation behind the printer.

Customized version of https://www.thingiverse.com/thing:45101 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=45101

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6vAWWUiu1Hs

Layer thickness 0.2mm Blower Cooling Fan 4020 Demension：40*40*20mm Voltage：12V Type of Current：Direct Current https://www.youtube.com/watch?v=JlNUAV7g5tc&pp=sAQA

TBS VTX Nano Onboard Flight Controller Mount 30.5 x 30.5.

The Nano Multi-Function expansion board is specifically designed for Arduino Nano, simplifying the complex wiring when multiple sensors are connected. It exposes all digital and analog IO ports with standard positive and negative power interfaces.

Here is a remix of the Arduino Nano v3 case designed by spradlinb, available on Thingiverse at https://www.thingiverse.com/thing:608121/.

Arduino nano holder.

Walksnail nano Camera

Ipod nano 5G

ipod nano 6th gen

Simple Arduino Nano Holder

Nano Talon Ground Cover

Arduino NANO box

Simple Arduino Nano Holder.

Arduino Nano case

Apple iPod nano 4G