effector and affector 3d models

I edited FolgerTech's magnetic kossel effector to suit my needs and decided to share it. This remix boasts a center distance of 21mm between the extruder and sensor. Note that this creation has not been printed or tested yet. ...Edit: After printing...

Custom made effector for replacing the stock one for my printer K280 - as I was to use the E3D V6 Hotend and BLTouch sensor. If you did like it and download it ;) ... ...as it was shared for free, please do the effort and drop me a generous LIKE: it...

This is the magnetic effector, expertly crafted by Huntley and tailored to fit the Nimble with precision adjustments. The Groove mount adapter that comes standard with the Nimble seamlessly integrates into this design, ensuring a secure and reliable...

This is my Anycubic Delta Linear Plus, a 3D printer equipped with a Duet WiFi module and a smart effector for precise control. I'm part of the vibrant 3D Printing World Italia community on Facebook, where like-minded individuals share knowledge and...

This is a custom version designed specifically for the smart effector and 40x40x10 fan. It requires four M2.5x20 screws to secure it properly. ...To assemble this part, I used brass tubes with an outer diameter of 4mm that I sourced from eBay, along...

... + DB9 RS232 + Brass Inserts M3 Original version: Magnetic attachment of auto-levelling probe. Used print blowing smaller and larger height. ...Employed: DB9 RS232 Serial Female to 9 Position Terminal Connector, Brass Inserts M3, magnet 8x2mm

Customization for 20mm Vertical Carriage Design For use with the Delta-Pi 3D printer and compatible Aerostock Magnetic Effector at Thingiverse http://www.thingiverse.com/thing:93042 Instructions to Follow The only changes are to install countersunk...

Effector variant for Molestock delta printer with E3D V6 hotend, designed for simple assembly and independent cooling fans. Original files can be found at https://www.thingiverse.com/thing:939825. ... Official page is available at...

This mount is specifically designed to accommodate the brand-new E3D V6 heat sink, replacing the existing Kossel Mini end-effector seamlessly as a drop-in solution. To ensure durability and prevent distortion, it's crucial to use high-temperature...

M3 nuts are inserted from the carriage's bottom, and socket cap screws are positioned beneath the z probe. ...This modification is based on version 4 (V4), with changes requested by Florian in version 5 (V5) that ensure screw heads sit outside the clamp...

It's designed a platform to be connected to the Kossel_effector_for_diamond_hotend_v2_40mm model found at http://www.thingiverse.com/thing:1102859 or sandwiched in with the fan, and is easily adhered. ... Dimensions: Servo measures 23 x 12.2 x 27...

Marlin settings for this effector are defined as follows: #define DELTA_EFFECTOR_OFFSET 25.0 // the distance the nozzle is set back from the center between rods spaced at 50mm If you use a BLTouch with it, define NOZZLE_TO_PROBE_OFFSET as { 0, 45,...

Marlin settings for this effector: "#define DELTA_EFFECTOR_OFFSET 25.0 // the distance the nozzle is set back from the center between rods spaced at 50mm" If you use a BLTouch with it: "#define NOZZLE_TO_PROBE_OFFSET { 0, 45, -4.175 }" You will need...

... There's the possibility of using two nuts, but screwing into plastic is normally enough. Tip : If you print this effector with PLA when in use, be sure to always ventilate it to avoid overheating and its deformation (it's a slicer parameter).

... to the rods is 37mm. Probe offset is 25mm. This product is an alpha prototype, and as such, it may not work entirely until all issues have been found and resolved. ...Please alert me to any potential problems or modifications you might want.

Main goals for this end effector include: -fitting a standard E3D V6 hotend -preventing the nozzle from getting too far beneath the arms -integrating hotend cooling for optimal performance -providing excellent wrap-around part cooling -featuring a...

Even printed in PETG, when printing PLA, the End effector would get hot enough to soften and deform. I also added a small vent in the Double Duct housing to channel a bit of air down, onto where the heater cartridge cables come out. Not sure if it...

This is a spacer for the underside of the predator effector for the probe magnet.

Update of Ultimate Anycubic Predator Effector (V6 & 4010 fans) for Haydn Magballs ;) Enjoy

Delta Kossel effector for LERDGE 2IN1 S1, or XCR3D 2IN1 S1.

Regular screws secure fan shrouds that clamp an E3DV6 onto a standard Kossel effector typically.

Standard Replacement Collar. ...Enables Original FLSun Effector to Operate with E3DV6.

The press-fit design was great, but when you print the duct, it's not always easy to get it right - a Kossel effector can move and jerk fast, and as the two extra fans mounted will create a bit more weight, I thought it would be safer to have a screw...

4 Versions with .step included * Version with a M6 bowden coupling and 1.0mm M12 Pitch Thread * Version with a M6 bowden coupling and 1.5mm M12 Pitch Thread * Version with bowden collect and 1.0mm M12 Pitch Thread * Version with bowden collect and...

The RepRap.cc effector for hotends is similar to the MendelMax's fixing technique and requires only three flat M3 nuts and screws. It supports Bowden Hotends with 1.75mm filament, 0.35mm nozzle, and 4 AD Pushfit options (Product ID: 95), as well as...

It has the heatsink mounted above the arm joints, and space for either a Volcano or regular V6 heaterblock, with an adjustable mount for an IR sensor. There's space for the 30mm fan, and dual blowers for print cooling. I'd honestly love to tidy this...

Here is a Remix of a Belt Tensioner Carriage designed specifically for use with Duet3D Delta Smart Effector PCB Carriages and RobotDigg linear rails. This upgraded version boasts an increased size and enhanced sturdiness, while eliminating the need...

I crafted it mainly to complement my smart effector and zesty nimble combo, which features three screws and nuts protruding from the bottom - a layout that made mounting the heatsink fan particularly challenging. In this design, the top portion...

Insert the E3d body into the effector and slide the mount into the slot in the E3D body lining up the 4 mount mounting holes with the holes in the effector. I used small thin washers with 4 screws designed for plastic threading from some old RC...

Hi, I've been using user swedishvaperuk's e3d v6 effector (https://www.thingiverse.com/thing:2767236) on my Anycubic Kossel linear plus for the past year and absolutely love it! However, I wanted to re-vist the part cooling situation and add a 5015...