ender 3 cable guide 3d models
875384 3d models found related to ender 3 cable guide.thingiverse
This is a cable guide for a direct drive modification to the Ender 3. It attaches to the bottom of the z axis motor cover. I have the PrinterMods kit, and they included lots of small plastic pieces for zip-tieing the cables. ... This seems a lot...
thingiverse
Guides the cables from the power supply up to the X axis and extruder on the Creality Ender 3. ... To assemble, from the rear of the machine slide the part (with the cables inside) into the frame next to the Z axis motor.
thingiverse
Cable guide to keep the cables and the bowden tube together on the Ender 3. I printed this in PLA, which works fine once it is installed. You can install it by twisting it around the cable and bowden tube. This is a bit finicky, unfortunately I...
thingiverse
** Other Ender 3 Parts.** [Tusk Fan Shroud](https://www.thingiverse.com/thing:3055926) [Z Endstop Bracket](https://www.thingiverse.com/thing:3057136) [Y Endstop Bracket](https://www.thingiverse.com/thing:3057132) [Cable...
myminifactory
---------------------------------------- Bobblejot Website Bobblejot GitHub Bobblejot Twitter Bobblejot Patreon ---------------------------------------- Just a very basic guide to keep the cables a bit neater at the rear of the machine. Just...
thingiverse
When I upgraded my Ender 3 to Direct Drive I moved the extruder/hot end wires to the front of the printer, so my Z max wouldn't be effected. I wanted a simple way to keep the wires from getting caught in front of the bed while it was printing. ...
thingiverse
This is a Cable Guide for the Creality Ender 3 Printbed. ...It is supposed to look alike to the design of the origininal cable holder.
thingiverse
added feet using a spacer that slides into the rails on the Ender 3 printers, and simply opened up the tube to allow the cable to slide in. should be easy enough to create a closing mechanism if needed but this holds cables fine as is. Small update...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
This is a cable guide for the z-axis of the ender 3. ...The holder on the spindle nut also has a guiding rail for filament.
thingiverse
This is a bracket that slides into the extrusion of the ender base and guides the head bed cables so they don't catch on the base, the STL is a newer version than the photos that has a wider opening and holes for zip ties.
thingiverse
This is a remix of Ender 3 S1 CableGuide. This clamp holds the ribbon cable in place close to the printer just above where it exits the base. It bolts to the Z-axis frame using a bolt and nut provided in the spare parts that should have come with...
thingiverse
This guide keeps the extruder and x motor cables in the plan normal to x (alongside the frame) so that it does not touch the build plate or the enclosure side. This design attaches to the frame by clipping on the profile rather than using the z...
prusaprinters
<p>It works. ...I switched back to Bowden drive, because Bowden drive is better on a stock Ender 3 pro (circa 2022)
cults3d
This is a cable guide for Ender 3/Ender 3 Pro. I used the Z braces kit for the printer, and having a direct drive modification (available in my Things), I found necessary to improve the cable management. In fact, my extruder cables were scraping...
thingiverse
This is a cable guide for Ender 3/Ender 3 Pro. I used the Z braces kit for the printer, and having a direct drive modification (available in my Things), I found necessary to improve the cable management. In fact, my extruder cables were scraping...
thingiverse
Had cable snagging after BMG installation, draw this with fusion360 so that the cable goes under the extruder. Now able to print tall prints and cable is not in the way. ... Needed for 5mm version: M5x16 + washer 2pcs M5 t-nut 2pcs zip ties ...
thingiverse
I found the anti snag piece here but didn´t really enjoy the idea of fasten it with screws. This design i similar to it´s predesessor but somewhat rounder and you don´t need any tools to mount it. ... I printed it with the mounting pins down to the...
thingiverse
This is a cable guide to route the cables from the back of the printer to the hotend in front of the X-axis. A lot of direct-drive mods require you to route the cables that way, or at least will benefit from it. You'll need at least one zip tie,...
thingiverse
Cable guide for Creality Ender 3 Axis Y and Z /!\ This is acctually made for the Ender 3 (classic), not the pro version /!\ Print the following files : Z axis : - 15x Segment - 15x Cover - 1x Up end Z - 1x Down end Z - 1x Down end cover Z - (You will...
cults3d
Cable guide for Creality Ender 3 Axis Y and Z Print the following files : Z axis : 15x Segment 15x Cover 1x Up end Z 1x Down end Z 1x Down end cover Z (You will need two M4 nuts and bolts [with the flatest heads possible (Max : 3-4mm)] to fix the...
thingiverse
Used to hold the extruder and X stepper cables clear of the Z lead screw and bed as it moves forward and back. ...Gide mounts onto the z stepper, and the cables are secured top the guide with a cable tie
thingiverse
I used a foot riser and used it on the top side made a angle to dodge the bed and made a swivel loop to move with the printer. Print both standing up. ... When you print something high it will pull the ring out of the base it does not damage anything...
thingiverse
New base design for the Ender 3 [Bulleye Extruder](https://www.thingiverse.com/thing:2759439/remixes) without the cable guide, what allows the use of the [chain links](https://www.thingiverse.com/thing:3132855) in the X axis.I just modificated the...
cults3d
The BEST cable guide for Creality Sprite Extruder. ...Can be clamped with a M3 x 10 mm screw or a cable tie. Uses the original mounting screws. Ender 3 S1 Ender 3 S1 Pro Ender 3 S1 Plus Ender CR-10 Smart
thingiverse
Simple cable guide to prevent cable abrasion behind PSU on the Ender 3 V2. Mounts directly to the end of the 80/20 extrusion in to the threaded holes using M5 screws of your choice with up to a .35 diameter head. I printed it in PETG with 20% infill,...
thingiverse
Having upgraded my Ender 3V2 to diy direct drive, I need something to restrain the hotend cable without installing an elaborate x-rail cable chain. So I come up with a sliding bearing ring, mounted on the underside of the top rail, through which the...