ender 3 filament guide 3d models

I simply flipped the cable holder over and cleared out the new metal extruder lever. A small hole in the center and a ziptie can be added if the cable wants to slip right out of it (luckily mine didn't). ...It now fits perfectly with Capricorn or other...

It is meant to be used with the dual gear extruder upgrade, if the alignement is wrong for your printer you can edit the Solidworks part (measurements 29.00 and 39.00 on the second layer), the rest of the design should adapt just fine.

I have been using the filament guide ring for my Ender 3 since I first printed with it, and I must say it's a must-have accessory. Thanks so much to the designer who created this fantastic design! However, after some time of use, two issues started...

I wanted to install the Prusa IR Filament Runout Sensor on my Ender 3. This is a revised version of https://www.thingiverse.com/thing:3127620, modified to accommodate the sensor. ...I needed an M2x80mm or longer screw and an M2 nut.

This remix combines the 2020 Snap On Filament Guide - Ender 3 / CR-10 by keithcorcoran and the Ender 3 - Z-Axis Bearing Stabilizer by benawhite.It is to be used with the CR-10 Bigger Z-Axis Manual Adjustment Knob (also Ender 3, CR-10 mini, Hictop,...

This is a critical filament guide for the Creality Ender 3 Printer, designed to prevent the filament from coming into contact with the greasy Z-axis lead screw. Installation is straightforward and should be easily understood by studying the...

This remix combines the 2020 Snap On Filament Guide - Ender 3 / CR-10 by keithcorcoran with the Ender 3 - Z-Axis Bearing Stabilizer created by benawhite. It is designed for use with the CR-10 Bigger Z-Axis Manual Adjustment Knob, which also fits the...

...If you haven't already upgraded to the Capricorn Bowden PTFE tubing, now is a great time - it's a fantastic upgrade over the OEM bowden tube that comes with the Ender 3 and has even higher heat resistance too. You can find it on Amazon at this link.

This remix combines the 2020 Snap On Filament Guide - Ender 3 / CR-10 by keithcorcoran and the Ender 3 - Z-Axis Bearing Stabilizer by benawhite.It is to be used with the CR-10 Bigger Z-Axis Manual Adjustment Knob (also Ender 3, CR-10 mini, Hictop,...

This is a devices that attaches to the top of the Creality Ender 3 and acts as both a filament guide and as a Z axis lead screw stabilizer.This devices is attached across the top and sandwiched under the factory spool holder. You will need two longer...

This is a devices that attaches to the top of the Creality Ender 3 and acts as both a filament guide and as a Z axis lead screw stabilizer.This devices is attached across the top and sandwiched under the factory spool holder. You will need two longer...

... hook. I just finished building 3 variations of this new filament guide from scratch along with several fixing options (including 6mm x 3mm Molybdenum magnets). ...As they don't remix this thing, I will add a new thing shortly and add a link here.

When installing direct drive and installing spool on the side of the printer, you need a filament guide. I got the idea from https://www.thingiverse.com/thing:4231868, but rebuild it. ... For better sliding, you need to put a small piece of PTFE tube.

I made significant changes to the original design so that the filament enters the drive unit directly, without any obstructions, regardless of its Z position in the extruder. The printed bearing was removed and replaced with a sturdy 1/16 inch...

... hole is a little bit higher. ... Additional it has a M3 hole underneath to hold it tight. V2 is 2mm higher than Version 1. The mounting arm is 2mm shorter. So it fits really good and the filament doesn't scratch at the entry hole of the extruder.

... entry hole is a little bit higher. ...Additional it has a M3 hole underneath to hold it tight. V2 is 2mm higher than Version 1. The mounting arm is 2mm shorter. So it fits really good and the filament doesn't scratch at the entry hole of the extruder.

When printing with special TPU filament, my biggest concern is that the extruder won't be able to feed it into the hot end. This bearing ring will tell me if it's turning and if the filament is being transported properly. I just need to look at the...

Additionally, I tweaked the round torus at the end to make it even smoother and added a cutout to simplify filament changes! Enjoy! ... Edit 08/07/18: A new version with a 4mm diameter hole has been added at the end for inserting a piece of PTFE-Tube...

That is a Filament Guide with filament sensor mount for an ender 3 v2. ...It may also work for other printers, but I haven't tested it.

I have customized the filament guide for the Ender 3 V2 (Neo). ...Additionally, I have added the feature that makes it easy to insert and remove the filament!

... as well. The side mount itself was a remix from this design: https://www.thingiverse.com/thing:2917932 Printer: Ender 3 V2 Support: Non on the main piece, with tree support on the top side mount. ... Infill 25% (this could likely be 10% or less)

This is a bracket and wheel for an Ender 3 Max with filament sensor. I wanted to mount my filament spool up on top, because I have multiple printers side by side and didn't like the spool mount that came with it and with the filament at an angle,...

When I printed Holspeed's Filament Roller Guide, I quickly discovered that it came into contact with my existing filament filter. This resulted in excessive friction, causing the roller to malfunction and fail to rotate smoothly. ...To resolve this...

When I printed Holspeed's Filament Roller Guide (https://www.thingiverse.com/thing:3052488), I realized that it touches the filament filter I was using. This caused friction, and the roller did not spin properly. ... So I added a roller guard to his...

Remixed filament guide for Ender 3 / PRO / V2 with metal dual gear extruder.

I remixed Hopper_Systems filament guide design so that button head bolts + T-nuts can be used to fasten the filament guide to the Ender 3 top frame.

Filament guide for Creality Ender 3 (or v2) with a cat trying catch it with a fish bone. ... https://www.facebook.com/pandoranium3d

Essential component for properly aligning the filament within the Ender 3/Ender 3 Pro extruder.

Ender 3 Side Filament Feeder Zola Lab Edition

I created a new guide featuring two rollers positioned above and below the filament, allowing it to be guided regardless of the Z axis's position. ... This design is entirely original, though its concept has been influenced by several other guides...