ender 3 filament guide 3d models

With my spool holder mounted on top, the filament had a sharp angle entering the inlet, which was likely due to my Ender 3/Pro setup. I appreciated the original design's use of PTFE tube as a guide and upgraded mine accordingly. Cutting a section...

The filament guide now sits perfectly perpendicular to the print bed.

This is a combination of a filament guide and a z-axis stabilizer, without the need of a bearing. It's printed at 100.3% scale and works fine as is. It's abit loose until you attach the screws again. ... The spacers are meant to space the original...

The opening at the bottom is 3.5mm so it can accommodate various filament diameters. It also helps set the filament at a slightly curved angle as it enters the extruder to avoid snaps and tugging problems. You can reposition the guide on the...

Simple remix, adapted to use generic, cheap 3-pin filament detection sensor you can buy online, such as http://bit.ly/2JjjDnk Also change dimensions a little to align the filament better on my Ender 3 pro. You will have to print parts for the bearing...

This is a lower filament guide designed for use with 608 ball bearings, which can be installed without removing the filament from the extruder. Parts and hardware needed: Part A (printed) Part B (printed) (1) 608 ball bearing (2) M3 x 20mm screws...

Remix of https://www.thingiverse.com/thing:4050500 I made the filament guide sit perpendicular to the bed. ... Category: 3D Printer Extruders

I decided to combine the two sources (thing:2967776 and thing:3303562) and add a simple ramp to guide the tubing at an angle, making it unnecessary to have any other filament guides at the top. The first design is meant to be flexible, so the ramp...

... I had this guide in use on my printer. ... After buying a BL-Touch, I had a spare end-switch, so I remixed this filament guide to hold the spare switch. ... Additional material: 2x M3 nuts Creality z-axis end-switch.

This is a filament guide that fits on the official Creality runout sensor carriage. ... Only the file for the bracket is included, for the other parts (spacers and ring) use the files from the original project.

the original was not firmly enough in the profile of the ender 3 pro, i fixed that and made it a little less angular.

This filament roller guide with tool holder is for mounting under the large filament sensor holder plate purchased from Aliexpress https://de.aliexpress.com/item/1005003236452992.html?gatewayAdapt= To mount the roll holder bracket, I simply used 4...

... Added an extended version of the clip to make it more stable. Added a remix of https://www.thingiverse.com/thing:4304283, made it shorter and have a bottleneck ending for the filament dust filter fit into my filament guide.

I created a filament guide that met my needs since I couldn't find one that fit perfectly so I designed this one using a bearing from an old extruder bracket left over from upgrading to all metal. This guide keeps the filament from catching on the...

... - 6mm fitting for 4x2 PTFE bowden tube - ~10cm 4x2 bowden tube - M3x18 screw (2 pcs.) You can see assembly process on photos! ... If you have no 6mm fitting you can try second vesion with tube holder *filament_guide_WITHOUT_FITTING.STL*

Filament bearing guide and runout sensor. Broadly based on https://www.thingiverse.com/thing:4079159 but designed from scratch, so more "inspired by", than remixed :-) Update 06/04/2021 - Completely re-designed from scratch in Fusion 360. Switch...

Normally, printing the guide clip isn't a necessity, but reprinting the guide arm is required due to filament wear on the loop where it feeds. I print using PLA without encountering any issues with either the clip or the guide arm. To produce both...

A version of my existing Filament Guide, except this time using the stock bearing that comes with the stock extruder. If you're replacing yours with a Metal Extruder, you can use the existing parts in this build, that's all you need and nothing...

A version of my existing Filament Guide, except this time using the stock bearing that comes with the stock extruder. If you're replacing yours with a Metal Extruder, you can use the existing parts in this build, that's all you need and nothing else....

I've been loving the filament guide, but I still wanted to add the Z support, so I simply took both models and mashed them together in tinkercad. I did measure, so the z support should be in roughly the right spot, but I still need to print it to...

This design is virtually identical to theroar's non-all-in-one filament guide, with the addition of a bottom and side wall that prevent it from tilting. These walls keep the entire structure stable. The bearing itself is simply a copy of theroar's...

I printed the Filament Roller Guide that was created by Holspeed on Thingiverse but I also wanted to mount a filament runout sensor so I remixed the filament guide to mate with the runout sensor that I had originally created for my CR10S that mounted...

I printed the Filament Roller Guide that was created by Holspeed but I also wanted to mount a filament runout sensor so I remixed the filament guide to mate with the runout sensor that I had originally created for my CR10S that mounted on the...

... This is a customized remix, featuring a 5mm offset on the top component for seamless use with an aluminum extruder on the Ender 3 Pro. I'd like to extend my gratitude to Dezhe for their contribution. ...Have fun experimenting!

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5CiFX1Yf8qr This is a remix which has a 5mm shifted top-part for using with an alu extruder on Ender 3 Pro. Thanks to Dezhe! ... Have phun!

This is a remix of https://www.thingiverse.com/thing:4683505 with the arm rotated 90 degrees to provide a nice bend for handling filament with a read-mounted spool such as from https://www.thingiverse.com/thing:4333835 The spool holder has its own...

M4 x 16mm bolt (spare part with my Ender 3, hopefully yours too). I've just left bracket unmodified. Bracket has one hole a litle bigger, push the M4 screw through. The second hole is smaller and it will be self tapped by that screw. Rotate...

This guide works seamlessly with both the standard extruder frame and the slightly taller double-gear extruder frame, which has a raised filament hole compared to the standard one. This design centers around this switch:...

Also after 1 month, I noticed the gear became loose and sometime was detached from base when changing filament. So I did this remix to address these minor issues. 1) The base's U shape was widened 3mm to insert smoothly and to match with the...

This is especially true because the original design is so easy to remove from the printer - so when swapping filaments just pull the filament out, remove the feeder, put new filament in, replace the feeder, and fit the filament into the bearing...