ender 3 linear rails 3d models

V-Slot Rail Covers to fit the rails on the Ender 3 and various other printers. These will fit snugly (unlike others available that don't fit well at all, either too tight or too loose) to keep dust and debris out of the crevasses of your...

Esto 1" square tubing for the bed frame, Uxcell 17x25mm bed screws, 450mm linear rails all around. The Z height is limited by the bed assembly, but I don't print tall objects. I print many small objects so I maximized the gantry travel. You should...

This is a piece for Ender 6 to use linear rails in X axis. ...

Designed a new hot end chain link end as my ender 3 has linear rails so there are not a lot of mounting options I used the top blower fans screws. I printed just fine with 15% infill at 0.16 layer height using Cura. Make sure to print it on is side...

It's remix of "Ender 5 MGN12H Linear Rail Conversion Kit" from SnakeP. I removed top of model so it can be installed with my DDE kit (Trianglelab). ... I RECOMMENDED printing on PETG, ASA, or ABS.

It's remix of "Ender 5 MGN12H Linear Rail Conversion Kit" from SnakeP. I removed top of model so it can be installed with my DDE kit (Trianglelab). ... I RECOMMENDED printing on PETG, ASA, or ABS.

Left and Right Brackets for mounting the Linear Rails for the Y-Axis inside the Frame You need 2 Linear Rails MGN12H 350mm and a few screws

I made this as minimalist as possible in order to not need to buy a lot of extra components and to avoid extra flex. Hardware: 3 x 300mm Linear Rails with MGN12H Block 6 x GT2 Idler Pulley 20 Teeth 5mm Bore 36-ish x M3 Slide in T Nuts OR M3 Hammer...

... 4 of these. one above and 1 below the gantry and one on each side on the top. there are more affordable linear rails online you dont need to buy these specifically but they are 350 mm long and will satisfy the length of each axis excluding z lol.

Ender 6 X rail adapter with support for a chain R18 10x20

Rear belt clip video installed on an Ender 5 Plus: https://www.youtube.com/watch?v=5KwS48xxb3w Front belt clip video installed on an Ender 5: https://www.youtube.com/watch?v=1vp6IQ8vMQI UPDATE 02/24/2020: The Hemera Linear Rail mount has been...

Minor design tweaks to improve print quality This is my second Core XY conversion kit for the Ender 5 with Linear rails. Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here:...

Minor design tweaks to improve print quality This is my second Core XY conversion kit for the Ender 5 with Linear rails. Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here:...

This is a spacer mod i made to enable me to use MGN12h linear rails on my Ender 6 as i do not have MGN9 available in my country. Thanks for the top cover design that i have already made initially from https://www.thingiverse.com/thing:4787779. It...

Dear All, For all Enthusiasts Wanting to Convert the Bed Axis into a Dual MGN12H Linear Rail System, I've Designed a Slider That Can Be Mounted with the Original Bed Aluminium Plate. To Get Started: * You Will Need: One of the M3 Screw Inlays and a...

Base for mounting direct drive on Ender 3 V2. For X MGN9 Linear Guide Kit purchased from ALI. For mounting on the bearing, I used M3x16mm screws with a countersunk head. The 23mm motor doesn't work very well with this extruder. Not enough power at...

This is my third Core XY conversion kit for the Ender 5 with Linear rails. As per the previous versions a big shout out to barnabyQ for his Ender 5 Pro 3D model over on Grabcad. This made things so much easier. This version resumes some of the...

Update 05.08.2023 Modification to mount a Hemera XS Revo extruder on an Ender 5 Plus with linear rails. Only M3 melt-in threads and screws are required. The X limit switch needs a spacer and the CR-Touch needs a holder, both of which I...

After upgrading to linear rails there was nothing to trigger the endstop so I re-designed the x-axis endstop mount. designed and oriented so that the metal clip naturally rested on the micro switch rather than against it, works in conjunction with...

After upgrading to linear rails there was nothing to trigger the endstop so I re-designed the x-axis endstop mount. designed and oriented so that the metal clip naturally rested on the micro switch rather than against it, works in conjunction with...

This is my third Core XY conversion kit for the Ender 5 with Linear rails. Previous versions here, updates at the bottom of the page. MK2: https://www.thingiverse.com/thing:4777606 Mk1: https://www.thingiverse.com/thing:4650517 As per the previous...

This is my third Core XY conversion kit for the Ender 5 with Linear rails. Previous versions here, updates at the bottom of the page. MK2: https://www.thingiverse.com/thing:4777606 Mk1: https://www.thingiverse.com/thing:4650517 As per the...

I have linear rails that blocked the way the bracket sits on the hot end plate. I also added some clearance for BLTouch and moved everything over just a little for improved alignment from my BMG All Metal Clone to the stock hot end. I also added...

......Since I have top mounted linear rails, the sides of the 2020 were available for mounting, and I moved everything outside to maximize the range of motion on the x-axis for klicky probe placement. Files should already be in the correct orientation.

MGN9C or MGN9H X-axis linear railM3 heat inserts Toolhead for :stock daughter boardstock 1x5015 part coolingstock hotend or E3D revo-cr hotend (not tested)New hotend fan coverV2 new :Adjusted 1mm higher belt position. ...Clamps adjusted.New hotend fan...

This is a remix of Harryb1991's RPI4 case with added rails for Ender 3 and CR-10

Mount for an SuperPinda/Pinda Probe for the Ender 3 Pro Linear Rail Afterburner Mod Addon for: https://www.thingiverse.com/thing:4572984Voron Afterburner Direct Drive Mount for CR-10/Ender 3/etc.by TroyJoachim August 18, 2020

This is a remix of the Ender 5 Linear Rail Mod but exclusively for the Y Axis. The reasoning behind this remix of mine is that the original thing doesn't account for using longer Linear Rails (350mm or more) which may be useful for some people. In...

Ender 3 Raspberry PI Mounting Case, No Hardware Top mount. ... This is my first remix/design.

Mounting on Ender 3: Slide onto square extrusion using two rails. The fit is very snug (file down slots between duftail and enclosure for a looser fit). Hardware: Enclosure: Use M3X6mm screws (tap with #4 x3/8 self-tapping screw) or #4 x3/8...