ender 3 modding 3d models

I recommend using my other remix of a different duct instead - my modification can be found in the comments (Fan_Mod_New_Version_Ender-3_v3.stl): https://www.thingiverse.com/thing:2814127/comments Or here: https://www.thingiverse.com/thing:3365114...

---------------------------------------- This is the second version of a linear rail mod for the Creality Ender 3 and the one I am using now. This mod was done to improve the belt path alignment and create a sturdier platform. With this mod, I...

---------------------------------------- ** My Other Ender 3 Parts: ** [Tusk Fan Shroud](https://www.thingiverse.com/thing:3055926) [Z Endstop Bracket](https://www.thingiverse.com/thing:3057136) [Y Endstop...

Not everyone likes them or wants to use them so this way you can just thread into the plastic body. AddedY_Limit_Switch_Bracket.stl & Y_Limit_Switch_Bracket_Offset.stl to mount the original Ender 3 Endstop to the right hand side of 2040 extrusion...

It's a drop in replacement for the strain relief cover for the Ender 3 Pro and probably other modelsThis is not a How-To document, this just shows how I modified my own printer. I have over 40 years of electronics experience and feel qualified to...

You can relocate the power supply for Ender 3, not PRO. ...You can use the adjustable feet and relocate the power supply, https://www.printables.com/model/317551-adjustable-feet.</p>

This mod is for adding a linear rail to the Creality Ender 3. I have these versions installed on my machine, and they are working well. Is this a necessary mod? Probably not. The Ender 3 is a well-built machine as it is. It's something that you can...

The MGN12H Mod adds an additional 3.5mm to the Y Offset on top of the original 7mm Offset. ---------------------------------------- This is a simple X Linear rail mod using an MGN9H rail, with a slightly increased Y offset due to the rail carriage,...

... to be used with two 300mm 2040 extrusions to tilt your printer 30 degrees. ...It should work with most ender 3 style printers. ... Hardware 12 x M5x10 12 x M5 t-nuts/hammerhead nuts I added fusion files for anyone who wants to make changes.

gantry mount: * add hole on gantry mount corresponding to additional holes made by Creality on Ender 3 V2 gantry (some first few production series of V2 don't have them but maybe someone will find them useful) * add some cable management elements...

IMPORTANT: you will need all the regular parts from kevinakasam's belted z mod but substitute file “1_leftV3.6” with the version I made and print the additional cable holder piece. ...I just used some random screws I had on hand but you can edit the...

This is a modification of the Satsana Ender 3 Fan Duct to fit an Ender 3D Pro direct drive with CR Touch. It has been further modified to split. There is a base that mounts to the printer and one bolt holds the Santsana to the base mount. This...

Fits a Noctua A9-14 (4pin) 12v fan - 92x92x14mm Original PSU fan had a 74dB peak noise level (as measured with my potato) After the mod the psu peak noise is 51dB (measured with the same potato). Support: YES. (there's a small piece in the corner...

This is a remix of a great compact design and should make the mod usable by non BLTouch users. There is more than enough room to put your own sensor bracket in there as I have. I've also made some changes, tightening up the tolerance for the blower...

**Post Squaring**: Loosen the bottom two screws and top two screws on the left side, then loosen and tighten the 3 T-Nuts on the right X gantry plate. 6. **Post Spread**: Move the gantry to the top of travel and loosen all four top screws only, then...

I wanted to use the 5010 fans I had spares of, so I remixed this to include one. Also removed some of the vents to force air over the mainboard. ... This is a remix from https://www.thingiverse.com/thing:398515

I would suggest printing this with the angled face flat on the bed; that way the force of the weight of the motor isn't completely perpendicular to the layers. ... I'm fairly new to 3d printing and couldn't easily find a model for moving the motor to...

Version 2 (October, 15th, 2020) changed a little bit the desing to allow the use of the top drawers without interfere with the screws of the front pulley Version 1 I modified the great design from DWS_design...

This is still a work-in-progress project that serves as a direct replacement for the control panel, effectively running a 60mm 12-volt fan.

I added another set of holes for another zip tie and added a rounded corner for a more even look.

<p>I wasn't a fan of the drawer on the E3V2 and needed a place for my Pi and power distribution board, this is that.</p> <p>Includes a button to turn on/off the machine via octoprint+relay on the front as well as a 2.5mm jack for a timelapse...

I wasn't a fan of the drawer on the E3V2 and needed a place for my Pi and power distribution board, this is that. Includes a button to turn on/off the machine via octoprint+relay on the front as well as a 2.5mm jack for a timelapse trigger. ...

I added another set of holes for another zip tie and added a rounded corner for a more even look.

MOD BULLSEYE_DUCT NOCTUA 40X40 ENDER-3 Merci au créateur de l’original: https://www.thingiverse.com/thing:2759439

-example printed using CookieCad Mermaid HOW TO APPLY -take off spool and remove cylinder -slide crytals over the top and all the way down *

Cover to shield cables from damage by sharp edges of molding. The cutout in my molding is 40x20mm. Double-check your dimensions before printing. You can remove the control panel for simpler access. ...Print two copies and snap them into place, it might...

hopefully you like this one

Simple cover to protect cables from being cut by sharp edges of extrusion. Cutaway in my extrusion is 40x20mm. Please check your dimensions before printing. You can remove the control box for easier access. ...Print two copies and snap them into...

This a remixed limit switch holder since the original limit switch adapter didn't fit at all. There was just no space for it. It bolts onto the extrusion with the motor mount and screws. ...No additional hardware is needed.

Update V2 -> Added extra space for capacitors (now two screws can fit), relocated screw placement, created fan cable hole, and aligned J62GM (awaiting testing). Update V1 -> Tested thoroughly and fully operational (additional pictures included),...