ender 3 pro y axis linear rail 3d models

Designed for stabilization, because printing at 100mm/s and upper creates too much resonance.

It is designed to fit a custom X- Belt tensioner for an Ender 3/Pro, especially the Tevo Tornado X Belt Tensioner for Ender 3 Pro (https://www.thingiverse.com/thing:3319649) but will probably fit anything with a diameter of 32 mm. All screws and nuts...

ENDER 3v2 and other models Cover for Z axis stepper motor. ... Ive added a dual Z axis setup on my E3V2 so decided with 2 of them they needed covering up!

Wire loom attachment for Z axis linear rail system for the X axis wires.

In an attempt to make the Creality Ender 3 Pro as quiet as possible, I figured the endstop switch clicking noises made during homing needed to go.It's important to note that I've installed a Creality V4.2.7 board as well as a BLTouch (so this may not...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

Belt Spacer Designed to Easily Adjust Spacing of Y-Belt When Installing Linear Rails. **Updated Version v2 Specifically for Machines with Rails, Belt Tightener, and Y-Motor Mount Already Installed. ... Watch My Complete Project Video at...

I was working on adding linear rails to my Ender 3, however with the Z axis linear rail setup I'm using, it originally requires to buy new screws for the Z axis, and at the time I was building it I didn't have any extra screws lying around. So I went...

Story time: Last year I ordered an Ender-3 X-Axis belt tensioner thinking it would be a drop fit with my tarantula but to no ones surprise it was not. So I remained determined to use it because I don't own an actual Ender-3 so I started designing an...

If you are looking for this, you probably know about the Z-axis problem of the Ender 3. This is an easy fix.HOW-TO!Step 1:Print all three parts.PLA - 200/55; 50mm/s; 6mm retrac. @25mm/s; 0.16mm; 100% fan; 50% infill; 15% 45° support 0.2mm...

The TronXY X5S Y Carriage (450mm Linear Rail) V1 is now available, featuring one side only - simply make a mirrored copy to print both sides and give it a try. This project is still in progress, with ongoing development and refinement. ... Version 1 is...

the holder fits on the CR10S pro V1 and V2 as well as on the ender 3. on the printer no screws need to be replaced or loosened just slide it on and mount the camera. the camera housing for the PI V1/V2 you get here:...

I have only tried this on the  Ender 3 pro; other printers may have the holes in the correct place.To check your lead screw - move the gantry to the top (as seen in photo) and measure gap. Then measure the gap closer to the stepper motor. I had a...

* M4x15 Bolts: Be cautious not to damage the Z-axis rail. If necessary, shorten these bolts using a Dremel before installation in loose condition. Avoid over-tightening. Materials: * 2 x 1.5 mm ordinary copper cable (black preferred) * Led Strip...

Anet A8 Linear Rail Y Axes Update This is a companion piece to https://www.thingiverse.com/thing:4276157, where all the parts were designed using SolidWorks 2018 and uploaded for public access. If you require alternative file formats, simply let me...

... axis guides, and made the clearance in the side wider for the larger screw head. The threaded portion has had the inner channel narrowed to fit the enders smaller pulley and the hole size has been change to accommodate whatever size that screw is.

... from the upgraded yellow springs. The next time I have a chance to check it again, I'll try to figure out what is going on and may update the design to support this other Ender 3 Pro configuration. ... Sorry if this has caused anyone a problem.

X Endstop for Creality Ender 3 / CR-7 made to fit with mgn12 linear rail

I was working on adding linear rails to my Ender 3, however with the [Z axis linear rail setup](https://www.thingiverse.com/make:899298) I'm using, it originally requires to buy new screws for the Z axis, and at the time I was building it I didn't...

... interfere with axis movement Required: - 4x M4 Washers used for bolts and as spacers either side of roller bearings. - 1x M4 Bolt (same type used on Y-axis) - 1x M4 Nut (nyloc recommended) 6 Parts Total: - 1x Body - 1x Bush - 2x Pullers - 2x Knobs

Y-axis engine mount for Ender 3 and similar printers with 4020 profiles. ... V2--> a fault in the motor screw spacing has been corrected If you have a bug, please comment on it and correct it in later versions Thank you

My part of design is a little bit sloppy, because I was too lazy to do it from scratch and used piece of my own mesh for railing mount. See screenshot for how to place on the buildplate ver.5: added a rib to compensate for plastic heating and...

I adapted the CR10 Z axis adapter for linear rail to make it compatible with my Tronxy X5S featuring an MGN12 type C linear guide block. My goal was to retain the original metal gantry while swapping out only the external wheels, leaving the internal...

https://learn.watterott.com/3d-printer/mk3-y-upgrade/assembly/ Hardware needed: V slot mounting: Same as rod holder by pekcitron Rail and carriage mounting: 10x M3x10mm Rails: 1x 330mm + 2 MGN12C carriages 1x 330mm + 1 MGN12C carriage If you want to...

(integrated supports since V2) Follow the instruction given in the link below to mount it. https://learn.watterott.com/3d-printer/mk3-y-upgrade/assembly/ Hardware needed: V slot mounting : Same as rod holder by pekcitron Rail and carriage mounting :...

Check out my other design for converting the Z-Axis to use dual lead screws and linear rods: https://www.thingiverse.com/thing:4817790 https://youtu.be/EMDsv_4jz4s https://youtu.be/bGszZp_2sEU This is part of a series of mod designs for the Mega Zero...

Position the mount to facilitate the installation of the caliper for precise axis calibration.

Positions x axis switch to allow MGN12 carriage to home. ...Works with the XChange system

Guide for the hotend wires if the Z-axis extruder motor is removed.

The front and rear Y rods are still used, but the carriage travels on 3 MGN12H linear rails. The main advantage the rails provide is a massive reduction in middle-of-bed sag caused by the deflection of the original smooth rods due to the weight of...